I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...
A new library/toolkit has been built that allows us to invoke the services of an nRF24L01 from a Java environment. Documentation and links to the Github project can be found...
Hi,
I am sending data from Android phone in every 200 ms to nRF8001. But sometimes I found there is a 50 ms or 100 ms delay. It looks like nRF8001 spending some time in...
Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
In the v16.0.0 SDK the settings struct size is 904 bytes, but in the nrfutil it's 803 (screenshots attached). I figured the settings in python don't include peer_data(64bytes...
I was in the process of integrating a NAND flash to my project. - MX35LFxGE4AB
Initially, I thought it would be good idea to use QSPI, but it seems to only support NOR flash...
Hi
Im struggling to use the ble_app_template_cpp within SDKv16. I am using the nrf52840 DK (PCA10056) and want to us the S140 SoftDevice. The example isn't built for either...
Hello everyone:
The problem is still not resolved
Test broad is PCA10056
Test code was modified by \SDK17.0\examples\peripheral\usbd_msc\pca10056\blank\ses
Try to...
I am using a thingy52 device and in that, added code of advertising and scanning from the sdk 16. Advertising is run successfully. But getting packet loss issue. So, I am...
Hi
Im developing an application that will wake up on RTC every 15 minutes. My issue is that when using idle_state_handle, which in turn calls sd_ble_app_wait, the RTC...
Hi,
Trying to figure out the current requirement on GPIO input, can you point me in the correct direction in how to figure out how much input current the GPIO on nrf9160...
Hi,
we are planning to add a 256 MByte NAND flash to our sensor project. I saw the example for NOR flash on the PCA10056 which is working fine. But due to costs we want...
Hi,I am using the nRF52840 development board, S140 and SDK16.0, I have some questions about data transmission on the UART.
I am trying to make a central device that is similar...
Hi,
I am working on a custom nrf52840 board and am having trouble connecting to the usb interface on the chip. After testing with the dev kit, the adafruit bootloader...
I trying to establish communications with a (non Nordic) beaconed 802.15.4 coordinator.
I've used some code from the wireless_uart_raw example but did not use the FSM. ...
Hello all,
I am having a problem to get SAADC to work with low power. I am using custom board with chip NRF52811, SDK 16.0.0.
I had turned on the SAADC_CONFIG_LP_MODE...
Hello Everyone,
I am using my custom board with nrf52832 SoC and developing my application firmware with sdk15.2 & softdevice v6.1.0.
In my application code, BLE scanning...
Hi,
We were trying out the LTE RX/TX test using the AT%XREFTEST command and undestood that for LTE RX testing ,an external signal generator is required. Is there any way...
Hello
I would like to know if there is a capability of a truly secured boot with the nRF53, starting with a secure bootloader in some locked or immutable memory - i.e. secure...
