I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hi,
We are programming our devices (nRF52833) in production using a Segger Flasher Portable PLUS.
We use reset after programming via SFR access.
Our devices will not...
I'm using the at cmd library ( commands like at_cmd_write_with_callback ) to communicate with the modem.
I'm trying to enable the nrf_modem library to enable OTA updates;...
Hello
in order to analyze reboot reson (HW \ SW) I use the following:
in case of kernel crash I usually get coldstack print, in this case I can analyze and understand...
Hi guys,
Based on the examples that I found in Zephyr samples documentation, I created the program where I am able to measure the voltage and temperature, and then send...
I tried running pc-ble-driver-py/advertising.py
my command was " python3 advertising.py NRF52 /dev/ttymxc4" and then I got following error
Traceback (most recent call...
Hello
nrf_drv_twi_rx and nrf_drv_twi_tx are non blocking calls?
in the SDK example, I see a while loop is used in the read call for instance which basically is blocking...
I am attempting to build a project with the command line tools as described in: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_programming.html, but it...
Dear all,
Can I achieve ble peripheral whitelist advertising without peer manager? (Assuming central address is already known)
Following are several places that I've...
I have been using the PPK II for about a month.
I just upgraded my nRFConnect to 3.7.1 and when I run the profiler, the PPK II is no longer visible (the big green window...
Hi,
We are design custom Board using nRF52840 SOC.
We are operating it in Normal mode, using internal DCDC converter
We have used configuration 5 from reference design...
Hi,
We are design custom Board using nRF52840 SOC.
We are operating it in Normal mode, using internal DCDC converter
We have used configuration 5 from reference design...
Hi, There. I am preparing to program a Mesh application based on nrf52840. The application supports the recovery from the points of power off.
So, I have a question. It...
Hi,
I'm working with the peripheral_uart example in ncs 1.6.1 and wanted to enable flow control for uart0, but do not see a way to do that.
How do I enable flow control...
Hi, There,
I develop a communication application based on a beaconing example on nRF52850 DK.
I don't know where I do wrongly. It is always stuck in the "bearer_handler_action_enqueue...
Hi,
I'm trying to collect modem trace from a custom nRF9160 board which is connected to the PC with a FTDI FT2232 UART-USB converter (USB vendor id 0406, product id 6010...
