I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Dear Nordic Team,
We are working on a solution where we want to only connect to a certain device if it is a known device and not accept any random requests.
We believe...
Hi ,Nordic
nrfx_err_t nrfx_pdm_buffer_set(int16_t * buffer, uint16_t buffer_length)
I wonder the buffer is PDM buffer or PCM buffer ?
also want to know that how...
Dear support team, The customer used ncs2.6.0 to run on nRF52840 to make matter over thread smart door lock. When stress testing the switch lock (repeat: password unlock ...
I 'm using zephyr to create a custom nrf52832 board .
I 'm using the Devicetree Visual Editor .
Any idea why I can 't select this specific display controller ?
The datasheet...
Hello, As for my peripheral BLE NUS service under NCS 1.9.2, when I search and connect it from my Windows PC running nRF Connect for Desktop BLE Standalone 4.0.0, I found...
I am sending data from iOS to a nRF5340DK. I have some code showing the TX/RX MTU Size:
Which shows: Updated MTU: TX: 527 RX: 498 bytes
But on the iOS/Controller...
Hello!
As stated in the subject, when I followed the steps in the chapter of running OTBR using Docker ( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/protocols...
Hi, am using the nrf52dk with nrf52832, nrf coonect sdk 2.5.1/ toolchain 2.5.2 and am building a prototype to aquire the signal from the ckp and cmp sensor in the car when...
Greetings,
We switched from nrf9160 to nrf9161 and got the first boards manufactured. NRF9160 has been working fine but we wanted improved GNSS functionality on board. ...
Hi all,
I have plenty of experience with the Old SDK, IAR/Keil/SES, nRF51, nRF52, Soft Device, etc. However, I'm new to the nRF Connect SDK, VS Code and nRF5340. I've successfully...
Please let us know which PINs of nrf5340 are used by BLE stack and which pins are used by peripherals like UART0 and UART1? We are converting our code from nrf connect V 1...
Hello,
We are evaluating MCU's for a low cost Central device that is extremely cost constrained. The nRF52805 and the nRF52810 both have the same RAM (24 KB) and FLASH ...
Hello,
I'm stuck in the nRF Connect SDK Fundamentals course on lesson 3, exercise 1. When opening the COM port to view the printk messages, I get an error when connecting...
Hi,
I am working with nRF5340 and nRF Connect v2.7.0. When I try the mass sample it works fine. When I take the code to my custom project, I have
ff.h no such file or...
Hi,
I am currently working on communicating between the nRF5340 DK and the nRF5340 Audio DK over BLE. Could you please share the information flow?
Warm regards, Rajendra...
