Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Board : Nrf52480 custom board
IDE: VSCODE
NRF version : 2.6.99
Zephyr Version : 1.6.0
Segger systemview: 3.54
I followed the instruction from Zephyr RTOS, for using...
Hi support Team,
I would like to know the SDK version to be used for nRF54L15.
Is there any link to know details regarding the configuration, flashing and example codes...
I want to advertise a custom service so my central can filter for it and have a device name and manufacturer. I have the following code but can only seem to do either the...
Hi all,
I want for confirm my findings concerning ERASEUICR. I want to be able to erase the UICR from inside my firmware for automatic testing purposes (no debugger is...
I think I have a failing PPK2.
I tested it with this circuit.
My DVM shows the correct current flow - 1.48 mA. The PPK2 shows 40 micro Amps.
Note that the battery...
Hello,
Using nrf9131-ek because the nrf9161 doesn't seems to have the capability of using an external RC oscillator.
Plans are there in the project with using some/many...
Hello,
Using nrf9131-ek because the nrf9161 doesn't seems to have the capability of using an external RC oscillator.
Plans are there in the project with using some/many...
i have used this case:devzone.nordicsemi.com/.../using-swo-with-nrf52-redux and add ENABLE_SWO but when i flash and use jlink swo viewer,it will have this problem.
...
Hello DevZone!
I am using a nrf5340 with the nrf Connect SDK v2.6.0. I have been running into an issue that has come up a few times on separate occasions. Basically, for...
Hi,
i develop my product ny ncs V2.6.0. when i view the code
I noticed the annotation, it says “Edge interrupt gives only 7 channels. It is not suitable for larger matrix...
Hi. I have some question regarding to Bluetooth 5.4 on Nordic platform
1. Can Nordic platform do Advertising Coding Selection? I saw some old old issue that the device...
Hi,
I have tried to update the nRF Connect for Desktop app (v.4.2.0 to v.5.0.2). Unfortunately, the process does not work through the end. Once the installation of the new...
I have to use 240 bytes for my sensor value to send in bluetooth. so i choosed to work on ble_app_att_mtu_throughput i need only pheripheral to work on it . i have to remove...
Hi, I was wondering if hosting more than one nrf Connect for desktop version on the same computer was possible. The reason is that I need to use both the old app LTE link...
