How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hello Support Team,
I am currently testing the new Channel Sounding feature on two nRF54L15 boards, on which I flashed your Channel Sounding samples ( initiator and reflector...
Content: I’m working on integrating the nRF7002 EK over SPI with an nRF54L15 using nRF Connect SDK v3.1.1 . While setting up the workspace, I noticed that the Wi-Fi driver...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
I used the nRF Audio Example to build a BLE audio device. I use the test tone generator functionality. I was previously using nRF Connect SDK 2.6.1 and the test tone generation...
I am an FAE with Ezurio, we have a customer who was running through the nRF Connect SDK Intermediate training on DevAcademy and they ran into issues with AuTerm in Lesson...
## Description
On the nRF54L15DK, the measured floor current increases significantly when the GPIO is configured for button edge detection.
### Observed Behavior
* Floor...
Hi,
I am quite new to nrf's and zephyr and I'm working on a product that requires Direct Test Mode functionality. I started with the DTM sample and am now looking at how...
Why do I often fail to compile the examples due to west? The prompt suggests that I need to upgrade west, but I am unable to do so?When directly upgrading West through VSCode...
The solution for "nRF Connect SDK Intermediate - Lesson 9 Exercise 5" does not appear to boot-up after flashing and gives the following output on the com port:
*** Booting...
Currently with the DECT NR+ modem API on nRF91x1 I can schedule rx operations in mode NRF_MODEM_DECT_PHY_RX_MODE_CONTINUOUS given to nrf_modem_dect_phy_rx via nrf_modem_dect_phy_rx_params...
Is there a way to create custom battery profiles of non rechargeable batteries for the nPM 2100 PMIC? Is the nPM Fuel Gauge board compatible with the nPM 2100 EK?
Hello,
I am using nRF5340 with nrf v2.7.99-cs2.
We have interfaced External flash MX25R over nRF5340's QSPI channel. We are using XiP as well and some part of code lies...
I'm developing a Bluetooth mesh lighting controller on a custom board using nRF Connect SDK v2.6.1. I'm trying to add a Sensor Server model to report energy usage, but I'm...
Environment : nRF52833, NCS v3.1.1
Hi. I evaluate PAwR project in my Solution.
PAwR is Fine. But get/set Tx Power is issue.
before add PAwR, My solution used common...
Hello,
I am developing a custom IoT device based on the nRF9151 SiP with a Qorvo QM13345 SP4T antenna switch controlled via RFFE 2.1 interface. All RFFE AT commands fail...
