Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi，
Background Information:
Our product, BLE near-infrared device , is undergoing CRA (Cyber Resilience Act) compliance assessment—specifically for the EU RED Cybersecurity...
This seems like a silly issue, but I cannot get the UART output from the nRF9151 DK. Attached is a project that outputs via both LOG and printk() to a Segger RTT viewer without...
Hello,
I am working on a simple Bluetooth Mesh application for light control.
I started from the provided samples: - github.com/.../light - github.com/.../light_switch...
I am trying to program an external board using the development kid following the instructions HERE .
I am using the debug out P20.
I have tried supplying the board frm...
Hi,
I am working on ncs 2.9.1 @ nRF54L15.
I followed this academy course to add a single channel saadc in simple mode:
ADC read works properly, but the current read...
i built a small breakout board for npm1300 (QEAAD0 2516AA) to experiment with it. the twi pins are wired to the i2c ports of a raspberry pi 4 to control it, and i have attached...
I do measure different values for source and ampere mode. On the nRF52 DK. Source Mode: disconnect SB9, Power Switch is off. Vout from PPK2 connected to nRF current measurement...
Hello,
We are using NRF5340 in our product and running automated hardware testing. As part of this process, we need to program the chip twice: once with a dedicated testing...
Hello,
I am using nrf52833-dk for making a ZigBee coordinator. I am using "network coordinator" sample code.
The project is making a ZigBee connection between "nrf52833...
My error message is that it works on a computer, but it doesn't work on the company computer. I'm not sure if it's the encryption software on the company computer, but I don...
I have a 5 year old design using a nrf52832 on a MDBT42Q module. The BLE option was placed on the PCB in 2020 and has been unoccupied since going into production. My customer...
Hello,
I am trying to build the sample/sensor/lps22hh project on nRF52840 DK and STEVAL-MKI220V1, but receive errors in build.
I have added an overlay file as in boards...
Hello, I need support regarding putting my device to low power mode (sleep) and waking up with a timer or GPIO input. I’m working on an application using the nRF9151 DK, with...
Hi! We're evaluating the nRF7002 with its DK. As part of that I'm trying to run the sample in ncs/sdk/v3.0.2/nrf/samples/wifi/raw_tx_packet. I build it with: `west build ...
Hi For the measure of the signal and related audio quality, we would like to measure the transport frame loss. We own two nRF5340 Audio DK. But to be honest at the moment...
