Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello all,
I use a nrf9160. In my program, I would like to use a watchdog to be sur than my application is running.
1. I would like to save some data in memory without...
I just downloaded nRF SDK 17.0.2 and installed Segger Embedded Studio V5.20a
I opened the blinky example for the nrf52840 (C:\Nordic\nRF5_SDK_17.0.2_d674dde\examples\peripheral...
Hi everyone!
I got a Nordic Thingy 91 and I have tested the sample Asset Tracker application. But now, I want to build and program my own application, I was reading this...
I have a problem with a call to sd_ble_gattc_read() made within on_primary_srv_discovery_rsp that is reading vendor service UUID and returns with NRF_ERROR_BUSY. I am following...
i am using mpu 9250 and and using https://github.com/Martinsbl/nrf5-mpu-examples this examples.
the question is can i use magnetometer on spi protocol?
because i have...
1. When I use NRF52832 as the ANCS client to get the notification attributes, if the data exceeds the size of a packet and requires multiple packet transfers, is it the BLE_GATTC_EVT_HVX...
Hello, I am working on a project which requires using FreeRTOS with the nrf9160. Setup: - Boards tested on:actinius icarus, Thingy91) - VS-Code with Ceedling as build tool...
Hi, I have implemented OTA DFU on Android with your official DFU library. We want the DFU to happen in background at a certain trigger (car driving, triggered from device...
Dear Members,
How can I connect via ANT+ to Garmin GSC10 ?
then display cadence and speed value in UART ?
Is it related with this function in ant_bsc_rx_d52_s212.uvprojx...
Hi
My problem is very simple but I don´t know how fix it.
I have a project in my work and it goes very well, but when I returned home,I have build It and it goes with...
Hello,
I'm having an issue with my nrf52832 with and ICM20948 IMU attached. My issue is related to wake up on motion. I believe I've set it right but I can't make it work...
Hi.
I have several issues when trying to respond to Direct Methods (using v1.4.0 of the SDK):
In azure_iot_hub.c:
evt.data.method.rid = atoi(topic->prop_bag[0].value...
Hi !
I am working with a NRF52832 and with SDK 15.2.
For my application, I need sometimes to deactivate the Softdevice to begin some radio tests.
So I have programmed...
I am doing the procedure described in the nRF52840 specification, figure 193 "UARTE reception with forced stop via STOPRX".
I am using 1Mbps with hardware flow control....
