Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hi, i would like to work with nrf52832 for my IoT idea. So my question is where do i start from to work with this particular SOC nrf52832 chip? My End product would have integrated...
Dear Madam/Sir,
I'm trying to compile the ble_proximity example on SEGGER Embedded Studio with SDK 12.3.0 and SoftDevice 2.0.1 to run on nRF51822 with PCA10001.
After...
Hey,
I have implemented the ble_hid_mouse example in the nRF52832, and implemented both central multilink and USBD in the nRF52840 dongle so that both boards are paired...
Hi,
We are using nRF52840 in our product for both Client and Server communication on BLE5. We are seeing an overall average time of 5+ seconds for the overall connect, data...
Hello everyone!
I have started to work with openthread recently, and now I have to build a mqttsn client into a stm32 uController. I'm doing that by using the spinel protocol...
Does the nrf52832 has some delay when the shortcut of END_START is enabeled in continuous receiving?What is the meaning of rx chain delay?Does RX chain delay in 2Msps mode...
I'm having problems getting the peer manager to work in a project forked from the ble_app_template on my nRF52-DK (using pca10040e, S112), complaining it can't initialize...
Hi, I am using ble_app_uart_saadc_timer_driven example, which work just fine when receiving data on smartphone (using nRF Connect app). Now I would also like to do the same...
Hi,
I'm using the Nrf52810 with softdevice S112 for the moment.
Question 1:
In ble_gap.h i see that there is a define BLE_GAP_WHITELIST_ADDR_MAX_COUNT (8). Is this realy...
Hi,
I am reading a voltage value from an analog sensor which changes values with 0.02V step. So, i need the accuracy up to 0.02V from ADC channels . But right now i am...
Hi,
I have project based on nRF52840 (using SDK 15.2) and I have a problem with properly adding ADC measurement using scheduler - description as below.
Problem description...
Hi
I want to create this example:
A major network,it include the subnet A and subnet B.
One node X,it belong to subnet A and subnet B.
If the node X was a function...
Hi
We currently working on nrf52 dk with SDK15.0.0 but we will use nrf52810 rather than nrf52832 due to cost.
As I know, nrf52810 doesn't have FPU compared to nrf52832...
