Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Dear Nordic Support Team, I am currently performing Matter certification testing on our device based on the nRF54L15 using NCS v3.1.1 (Matter SDK 1.4.2). I am using the Matter...
Hi, support team,
I am conducting self-testing on a device developed with NCS 3.1.1, using the test versions corresponding to v2.13+summer2025 and Matter 1.4.2.
I...
Hello, Nordic Team! I am conducting Matter Test Harness testing and have successfully built the test environment. However, I am encountering some issues during test execution...
Using nrf5 SDK (not connect):
I have a RTC2_IRQHandler that is correctly being called.
rather than:
void RTC2_IRQHandler() {
if (mode == 2) {
handleMode2();
}...
Hello,
We are in the final stages of development and are trying to tune our device to perform its best in noisy environments:
We are using nRF52833 SOC as a central...
Hello,
We are using 2 nRF5340-based devices running:
samples/bluetooth/periodic_adv_rsp
samples/bluetooth/periodic_sync_rsp
with the PAwR configuration (modified...
I am evaluating the board nrf3054-dk + nrf7002-ek I build and run the sample project net/samples/wifi/shell on my board when I compiled the project, I added the following...
The blinky example from the official website can be programmed, but after opening the code and compiling with SES to generate the hex file, it cannot be programmed. An MBR...
I think variations on this question have been posted before but they all seem to be very old. I'd like to use the Bluetooth 5.2 LE Power Control features that involve exchanges...
I am evaluating the board nrf3054-dk + nrf7002-ek I build and run the sample project net/samples/wifi/shell on my board I tested the wifi shell with some personal encryptions...
Hi!
I just upgraded a product we developed using a Fanstel BT840X module (nrf52840 with a Skyworks SKY66112 amplifier) from SDK 2.3.0 to SDK 3.1.1 and I noticed that our...
I'm planning on using an e-ink display with my custom PCB . But when I add/enable the e-ink display node in my device tree, the TF-M code throws an exception in /ncs/v3.2...
Hi,
The attached screenshot shows a section of an air-trace for the 5340 running a commercial LE Audio stack. From the rising edge of the logic inputs, it can be seen that...
Hi List, I am using ZMS to log data. While performing stress tests, I see few issues:
Including zms in the projects makes the application boot time delayed. The delay...
