Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
Environment: nRF SDK 1.9.1, VS Code 1.66.2
Without making any changes, I can build and flash the iso_receive sample but it fails with a -5 error code (EIO) on this...
This is a cross-post from my question on StackOverflow here . This might be a more appropriate channel for this question.
I have a custom board using the u-blox BMD-350...
Dear Nordic guys,
We are going to produce large number of BLE beacon devices and would like to label the BLE address on each device. We are using the default mac address...
How Can I store information about button port ? I have two buttons P1.02 and P0.02. I have
And I have one function to init button
the most interesting is callback...
Hello to all,
Below are the setup details I'm using:
nRF52840 DevKit
SDK: nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
Segger Embedded Studio 4.16
I am working...
I'm trying to run LTE/BLE Gateway sample on nRF9160DK , i followed all the instruction in the sample instructions.
The Jlink RTT for nRF52840 and LTE-Link Monitor logs are...
Hi nice people, I am working on developing using visual studio and Make environment. I am trying to function UART tx/rx interrupt works but no luck. The TX and RX works perfect...
Hello, I've been trying to launch zephyr SPI example, but I'm having issues with SPI sending anything. The code itself does not throw any errors, and it seems like my board...
hello sir ,
i am using thigy91 board and uploaded the asset tracker application code from ncs sample code . ii am getting humidity data on my azure cloud .but there was...
Hello everyone!
We are using nRF51822 SoC together with s130 Softdevice. nRF5 SDK v12.3.0 is used for firmware development together with the Segger Embedded Studio.
Among...
Hardware: nrf9160DK Modem FW: v1.3.1 We have been evaluating and configuring our proprietary application for NB-IoT, which is initially designed for LTE-M (CAT-M1). The Application...
Hello,
I'm using a central device that lists all nearby peripheral devices by their MAC addresses like so:
but I also want to list the names of the devices as they...
Hi Nordic,
We are preparing to validate a product that contains the UBlox BMD-340 with the Nordic Softdevice. We would like to use the Nordic Semiconductor “nRF Connect...
Hello!
I have used most of the GPIO pins on the nRF52DK, and most of them work. But I cannot get pin 21 to behave. I want to use it as an input. I have configured it as...
