Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello, I want to scan all ble devices present near by nrf52-dk and process the data in my application. I am unable to find the scanning ble device code in nrf52 sdk. I am...
Shalom!
I want my code example to be able to run on both the nRF9160 and the Thingy91. I ran the SES Open nRF project menu twice and have two separate build folders under...
Comparing Current Consumption Between NRF52840 and NRF5340
Loading Zephyr HR sample code on both.
Connected to each using NRF connect and subscribed to HR UUID.
Measured...
Hi,
I understand that we have several types of sec_modes.
However, regarding modes with MITM - I don't understand how exactly those modes protect from MITM. What does...
Hello,
I started working with microcontrollers recently, I'm having issues with getting started with software development on an MS46SF11 module from Minew based on the nRF52805...
Hello. Developed with nrf52832 (S132 v7.0.1, SDK v16.0.0).
I want to get the data stored in Scan Response, but I don't know how to do it. Is there a good way to receive...
Because the GPS will continue to output data after starting, in order not to block the main thread, I placed it in another thread, but I found that when my main thread did...
It is not clear from the website whether Nordic has produced an LE audio chip/board, and if/when it will be available for purchase? Does anyone have any info on it?
Hi,
We are porting our application from nRF Zigbee & Thread SDK to NCS.
On the ZIgbee side, we have been using this methods:
1. zb_zdo_find_bind_src(): to check...
I'm working on a project that has multiple custom partition manager configuration file that are implemented based on the instructions provided in this section of the partition...
Hi,
yesterday, I met the same situation as here . But now, I can't even see one log, even after I annotated the code related twi and just remained some “NRF_LOG_INFO（）”...
Hi,
I am using SDK 17.0.2 for a simple scanner project, where nordic SoC is communicating with main MCU via SPI. The code starts normally on nRF52832, but on nRF52833, it...
Hi,
I am running the example ble_app_att_mtu_throughput with the nRF5 SDK on two nRF52840-DK dev kits. I have flashed both dev kits with S140 soft devices prior to flashing...
We are finalizing a product that has a BL652 (nRF52832) in the main unit and a BL651 (nRF52810) in a remote control unit. We are trying to get our regulatory radio testing...
