to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hello Group,
I got an error when I tried to “Open nRF Connect SDK Project” from the Segger Embedded Studio.
Do have any idea how to fix it? (the attached here my process...
Background:
Custom boards
SDK 15.2.0
SoftDevice: s140_nrf52_6.1.0
Hello,
We recently updated our project to use 2M PHY instead of the default 1M PHY. Our device...
Hello!
When looking at the central example ble_app_multilink_central in sdk_config.h, I found out that all links are considered central, with NRF_SDH_BLE_PERIPHERAL_LINK_COUNT...
Since the beacon will run on CR2032, I'm trying to minimize power concumption.
NOTE: All measured using nRF52-DK + PPK2 configuration
The online profiler says that if...
Hi all,
I have evaluated the performance with ble mesh on nrf52840 board on zephyr system.
when I use ble sniffer(wireshark) to catch the package I fond that every message...
Hello sir ,
I have successfully uploaded hello_word code from sample and i got" Hello_word" printed on lte monitor 's display using nrf9160.
now am trying same thing with...
Hi,
I would like to use the Event Manager for a product that is currently planned to use a Nordic product; however, I would like to be able to port the firmware (or parts...
Hi,
I am using ncs 1.5.2, and want to create a FOTA image. I am successfully able to build, flash and confirm the image, but am unable to set the version number of the image...
This is the errors , please help, to successfully create .hex file
If you want to look after full log details .......
Building firmware west build --build-dir c:\Users...
I bought a thingy91 module with ibasis scheduler on board. When I made the first installation of the mfw_nrf9160_1.3.1.zip software and the thingy91_asset_tracker_v2_ltem_2022...
I'm building a simple application using I2C to read sensor data (BNO055). I confirmed I2C and my sensor are all configured appropriately and working smoothly, but when I added...
Hi,
I'm using the mqtt_simple example to develop a new application.
I want you to tell me what lines of code I need to add for the nRF9160 to work in the minimum power...
Hi,
I am working with NRF52840 DK, from this i am using KEIL IDE. I got some error while opening the KEIL SW like Cannot set path to software packs. Make sure that RTEPATH...
Hi,
My customer use nRF5340 as their master control IC, which will connect with lots of peripheral.
They are considering about simulate a uart with GPIO.
What's the...
I have designed a custom board for the nrf52840 and upon testing it in the nrf connect sdk (using a JLink), I can only see the board when it's in bootloader mode. When it...
