Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I installed NRF connect SDK,
after installation I navigate from NRF connect desktop app -> Toolchain Manager
V1.71 is installed in D:\Nordic_App\Nordic_SDK\nCS...
I'm using VS 1.7.1 on Windows 10, with the nrf9160dk_nrf9160_ns
Playing around with myFirstApp from the VS Youtube Tutorials, I wanted to redirect output to uart2 and map...
I followed the getting started guide for Ubuntu:
https://docs.zephyrproject.org/latest/getting_started/index.html
I can build Blinky, but when building my project I get...
Hey, I'm starting a new project and I think a very good fit for this would be to have all of my code in an application chip and use a nrf52840 trough USB as a connectivity...
SD140
Our Central Application is scanning to connect to a peripheral's MAC address. When the scanned address matches, we call sd_ble_gap_connect(p_addr,..). But, it is...
Hello! I'm trying to reload CMake in an nRF-Connect-SDK project in the CLion IDE. I've been using this guide: https://blog.jetbrains.com/clion/2021/04/using-nrf52-with-cmake...
Hello,
I am writing the device tree for our custom board, which uses an nRF9160 SiP. This approach to configuring the hardware
is new to me, since my experience is with...
Hello,
We are attempting to track down a rare bug in our code that causes the device to occasionally hard fault.
We have been able to catch it three times, twice where...
Hi,
When I connect nRF52833-DK device to the (Windows 10) system, its JLink UART (COM) Port disappears after some time (in about 4 to 5 minutes.) The following screenshot...
hello Nordic
i work with nrf52840 , .. want to move to ncs 1.8
seems that moving to ncs 1.8 forces me to update to zephyr-sdk-0.13.2 (from 0.12.4)
is it really a must...
Hello,
I have added the line CONFIG_DEBUG_PORT_ACCESS=y in prj.conf file and now the project does not open in Segger Embedded Studio (SES).
I am getting this error,
...
Hi,
I am building my Project in an out-of-tree form and up to this point I solely used Segger Embedded Studio to compile our project. I am using a custom board with an nrf9160...
Hi All!
I am using VS CODE studio as an IDE for nrf9160 FW development. Blinky app compiled and work perfectly. But when I compiled the asset tracker/cloud client it gives...
In my code, the parameter definitions like this :
In my application, I used SAADC in SEGGER to convert my analog sensor input to digital and then i want to sent...
