Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello,
My board is connected to Gyro, Magneto sensor.
And board is sleep and wake-up by GPIO.
It usually works well. But time to time after wake-up from sleep mode...
Good Morning!
I try to update the modem firmware of a nRF9160 chip.
When I connect it with the nRF Connect v3.6.1 - Programmer (v1.4.10) and try to update the modem with...
Hi all
For the nRF52832, the total maximum sink and source current is recommended to be 15mA in this devzone entry .
Unfortunately, it seems like there is still no value...
I want to add an external button that mimics the properties of the buttons in the nRF52 DK. I read that the switches are all active low, so I assume that this means they are...
Hi,
in peer_manager.h and id_manager.h the docs say a function can return
BLE_GAP_ERROR_WHITELIST_IN_USE
But the error code is called
BLE_ERROR_GAP_WHITELIST_IN_USE...
Hello,
I have an nRF52840 on a custom board. The nRF52840 has been pre-flashed with the Adafruit UF2 bootloader for early development exploration. As the project moves forward...
Using SDK15.3 and S140
following from my previous support request regarding TWI sleep current, I got the newer AIS2DW12 accelerometer and I have successfully connected...
Hello everyone!
I want to develop and app the sends some sensors data over BLE.
I am trying the peripheral_uart sample of the NRF Connect SDK but it seems that I cant...
Hi, there:
based on \\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart\pca10040\s132, I need add justworks BLE secure connection.
Do you have any document...
Hello, I want to use Multiple Connection (Multiperipheral sample) to connect with multiple IOS phones at the same time to implement UART. Currently, up to 9 units are set...
I am trying to advertise the shotend name of the device no the complete local name, so code looks like follow
After scanning I can still find the name in the advertisement...
Hello, we are using nordic SDK 16.0 and mesh SDK 4.2.0.
In our project, sometimes at the start of the program, we are running into line 280 of mesh_config.c, a debug assert...
Hi, I am using nRF Connect SDK 1.5.1 with the nRF9160 Modem Firmware 1.3.0
I have implemented an application on the thingy91 with the gps driver (continuous mode) and the...
Hi,
I want to build a mesh network which includes least 12 server node an 1 client node.
I used light_switch example to send 12 byte message packets to client node from...
Hello, in my project i simultaneously use MPR121 touch sensor controller and GPS module connected to UART0 of nRF52840 (custom board). To handle touch events, i use MPR121...
