Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Was wondering if anyone knew why this fault might be triggered?
It triggers when I try to use SPI0 and LTE together.
AT host is disabled.
The code stops here during...
While trying to utilize the TEMP peripheral today, I found that after the event handler returns a single reading the application does not continue to run. Any actions that...
Hi,
I got the nRF connect sdk downloaded and I can build zephyr projects for the nrf5340_dk_nrf5340. I somehow fail t find the sample projects as mention in
https:/...
Hi all,
I have a question regarding the difference between the nRF51822XX AC and nRF51822XX AA during the configuration of IROM and IRAM in Keil software.
I know that...
To the kind attention of Nordic support team,
We are going to use nRF52833 in our products, and we would like to embed in our PC side software (driver) a custom version...
Hi there,
I'm developing a custom board that integrates a NRF52840 based BLE module from Raytac. I was wondering if it is possible to upload the Adafruit nrf52 bootloader...
Hi,
I am implementing LESC on nRF52810 using an example.
Unfortunately, I didn't find any examples.
So, I am programming the PCA10040e with reference to the PCA10040...
Hi,
I am new to NORDIC dev and I find its ppi is really useful but also difficult to understand.
Now my device may be connected the truck engine to count the engine speed...
Hello Team.
I have NRF52840 Development Kit. here is description, what I want to do and How I am doing.
I will send command on terminal and kit will start scanning for...
Hi,
I developed a product using nRF52810 and am now preparing for mass production.
However, since I have no experience in mass production of Bluetooth, I would like...
Hello my current setup use :
nRF52 dev kit
Segger Embedded Studio V4.4
SDK160098a08e2
s132
nRF connect on a iPod touch
I can compile and once connected appreciate...
I am looking for example code on the EV-BT840(832)-V4 dev kit. I can program it with the hex file and it works, but when I program with the nR52 SDK example codes thru Segger...
I am trying Bluetooth mesh light-switch application on microbit, and I have flashed with same light code on multiple microbit devices, Though all the devices are getting detected...
Hi! I am currently writing a DMA driver for UARTE which with the goal of being able to handle large data transmissions with little software intervention as well as handling...
Hi Team,
We are using nRF9160 DK, We tested the asset tracking application with the DK. It is connected to nRF cloud and the data is sent from the DK to cloud. This is...
