I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
I'm seeing inconsistency in reading the ICCID from the nRF9160 modem with modem _info _string _get (MODEM _INFO _ICCID , mystr ,strlen (mystr ) ) ;. All other modem_info calls...
Hello Nordic DevZone Support,
I hope this message finds you well.
I am currently working on a project using the SEGGER Embedded Studio with Nordic products and I am trying...
This information is printed all the time while the debug is running at full speed What is the reason for this?
If it is not debug, the program runs normally
I want to develop some applications on top of Google Fast Pair. Created the fast pair input device application with the SDK version 2.7.0 rc1 and built with prj.config
...
Hi,
I have working with Bootloader development on nrf52840 controller, for that i followed devacedemy course for firmware update using Uart and able to update firmware using...
Hi,
I get a Mcu Mgr Error: 10 Group: 1, when I
start OTA on Android smart phone
interrupt during upload by disabling BLE on the phone
enable BLE again
retry OTA...
Hello,
I was using VS Code earlier today creating different build configurations for our hardware (nrf52840 and nrf9160 based) and everything was fine. I restarted the application...
I am currently using two nRF52840s to create a transmitter, one that acquires data and transmits it as advertisement data, and a receiver that receives data from the advertisement...
We are using nRF52833 with Softdevice S113 for BLE.
in the OS_Idle function, nrf_pwr_mgmt_run is called.
But never comes out of sleep.
Is there a need to call nrf_drv_power_sleepevt_init...
Good morning,
I am developing a RAK4631 (Nordic nRF52840 + Semtech LoRa SX1262) and now I need to manage the power consumption. My environment today is a VSCode/PlatformIO...
i am working with nrf52840 with nrf5-sdk 17.1.0 and with segger embedded studio 5.42a i am having trouble build a project and it is giving below warnings: Building 'main_app...
Hi,
I am trying to test the ICM42670 sensor using nRF9160 with Zephyr V2.6.0 and I am getting an errors when I init the sensor:
unexpected RESET_DONE_INT value, 0
ICM42670...
I’m using the nRF52832 with SDK 14.2.0 and would like to implement AES-128 CCM. Could you provide relevant documentation or instructions on how to achieve this?
I was developing my development kit with onboard sensors and other ICs. So, I was looking into NRF52 DK schematics and documentation. the problem is that the interface/debugger...
