I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi,
I am currently building software on NRF 52810 and softdevice version is s112 7.0.1. I have one service which has three characteristics. When I add either a new service...
I've been trying to install the newest nRF Connect SDK using the Toolchain Manager with the appimage The toolchain and SDK installations seem to be successful however when...
Hi. We have a custom board with an nrf1960, which we use to communicate with Azure IoT Hub over LTE-M. We are updating from NCS 2.4.2 and modem firmware 1.3.4 to NCS 2.7.0...
Hello,
We are currently in the process of developing a custom board containing the nrf5340, which will act as a central for HR devices and a peripheral for data transfers...
Hi
Can someone help out?
Why is there an empty PDU after every notification(length shown in trace with 277, my payload is 244). Are all packets with the same EVENT COUNT...
Hello!
Since we are moving from the prototype phase of our project to the pre-production phase, we have developed a custom board which utilizes the ISP2454, nRF54L15 SoC...
Hi,
I want to develop a new project without using NCS way. For this project, I didn't use the Kconfig and deviceTree.
The hardware I use is NRF54L15-DK.
My purpose is...
Hello, the CTE signal for Bluetooth AoA (Angle of Arrival) positioning is primarily transmitted over BLE advertising channels (37, 38, 39), corresponding to frequencies of...
Hi everyone,
I'm developing a BLE application where I measure throughput between an nRF5340DK acting as peripheral and an nRF52 Dongle as the central (using a Python script...
Hi everyone,
I'm currently working on measuring the power consumption of the 9160DK board and following the guide: Getting started with current measurements on the nRF9160...
We're trying to measure supply current used by the NRF9151 DK but have discovered that the current measurment connector (P22) only includes current supplied to VDD, and that...
Hi
I connected RF Connect for Desktop to "nRF54L15_DK" in my Desktop
when I want to use Direct Test Mode,press Start test bottom,the log show "DTM setup reset command...
Performance on hardware (cc3xx) is significantly slower than performance on software (oberon). Does anyone have a good explanation for this? I have also tested ECDSA and can...
Hello Sir,
I am currently working with the boards:52840dk and ncs:2.9.1
Regarding the issue of failed mcuboot upgrade after writing the upgrade firmware using flash APIs...
I run the system_off example without the system actually going off, by removing all the calls to start the system_off worker. Instead of going to off, I let the system enter...
