Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
There's a few threads out there with similar questions, but I haven't seen a direct answer to this.
If I build with nrf5340dk_nrf5340_cpuapp, can I use the entire application...
Hi,all~
The program runs on nRF52833. At the beginning, MCU sends data to nRF52833 through serial port, and the data can be received correctly(pic one）. When I use THE...
I currently have an issue where by the Chip-Select is not toggled at all when configuring the csn pin to pin <18> on the Nrf52840 using Zephyr (version 2.7.1).
See dts configuration...
Hi All!
I am using NCS v2.0.0 and nrf52820 custom board and an example to test is radio test . I tested that example with nrf52833DK , code is executing/ printing messages...
Hi!
I'm developping a battery powered product, so the power consumption is important. I need to multiple an array point by point with an array (hamming window) that I store...
Hello support,
Your choice of 201 size component packages are not ideal for manufacturing (and HW debug). I understand some of the reasoning especially on 21540 antenna...
Hi,
I'm trying to implement zigbee into our application. For testing purposes I start with the example code, and I use the multiprotocol template as a starting point.
...
Hi
I am trying to migrate my project to newest NCS v2.0.0 but is struggling figuring out how to configure SPI2 slave operation mode.
The project is currently running v1...
Dear Nordic Team,
your chip above is on 52 weeks lead time, so here is the question:
a) I can spot inventory for the 8 channel version: nRF24AP2-8CHQ32 - would this...
Hi,
We are trying to add lwm2m (client) into light bulb sample (matter).
It results a redefinition of gethosname : CONFIG_LWM2M defines CONFIG_NET_SOCKETS_POSIX_NAMES...
Hi,
I have a nRF5340 DK (not the audio DK). I read the specification of nRF5340 Audio DK and found that it supports LC3 codec. However, I want to ask, is it possible to...
Hi,
I'm trying to measure the current consumption of the nRF9160 DK using a Nordic PPK 2 in various modes. Through reading up various documentation regarding this, I have...
I've installed nRF Connect and VSCode on a MacBook Air M1. Whenever I try to build my existing firmware that builds fine under Windows, I get the following error:
The terminal...
Hello together,
I have my own MAC addresses and want to make Zephyr use them. How can I do that?
What I found out is that the firmware read the MAC from settings "bt/id...
From everything I've read, I should be able to see log output in the "LTE Link Monitor" when logging is enabled. Instead, it appears to freeze up the LTE Link Monitor and...
