Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hello,
I am working on a project which requires radio transmitter and receiver to work in sync with the SPI. So the setup is as follows the Transmitter transmits a signal...
Hi,
I am trying to write my own dfu updater for the NRF51 chip and I am stuck trying to make sense of the actual DFU sequence described here infocenter.nordicsemi.com/index...
I am trying to set up mqtt between 2 nrf52s and rpi3 with the examples of sdk 15.0.2. I am very new to nrf52, rpi3 and networking. I have read everything needed as much as...
Let's send a string over UART. RTS signal will go low (active). So far, so good.
The problem is that RTS remains active even after sending is done. And because it is still...
I have two boards. I ran the exact same commands on both boards. The commands flash the same bootloader+app+softdevice+app settings hex file. One board reboots into the application...
Hello,
Setup: Running Ubuntu 18.04 inside Windows Host (using VMWare).
Device: nrf52840DK
Operating System (used for development): RIOT
I would like to communicate...
Hi,
I am running IoT LWM2m example. Everything were going fine since yesterday. when I do hcitool lescan, i see following output:
hcitool lescan LE Scan ... 28:45:8B...
I am using the ble_blinky example (s132) and want to increase the number of characteristics. I get the error code 4. I think the storage capacity is not the reason why I can...
Hi Team Nordic,
I started developing a project using SDK 15 using DK nrf52840 .
I went through several threads and started by creating a test folder inside example directory...
Hello,
I have the proximity example updating the battery service value fine using the provided nrf_drv_saadc.h driver. When converting the saadc driver to NRFX (nrfx_saadc...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi,
It seems to me that unused GPIO pins can stay float. However, earlier questions made me less confident.
Is firmware setting is enough?
Thanks,
Daniel
1. Is it reasonable easy to get a stable throughput over 1Mbps at a 3 meters range? 2. How much CPU resource is available at above situation? Or how many DMIPS is left at...
Hi
I am working with S130, sdk12.3 NRF51422_xxac
I have been successfully testing bootloader DFU example (secure_dfu_secure_dfu_ble_s130_pca10028) on the NRF51 dongle...
