I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I am trying to get a SST25 spi flash running, but the jedec,spi-nor driver does only partially work.
As i understand now the jedec,spi-nor driver only works with CFI compatible...
Hi, I am experiencing low power issues on a nRF52840 DK 3.0.2 board which I have not seen on another one with version 3.0.0. I do not know the root cause yet.
For my investigations...
Hi
I am powering the nRF52840 from a 3.3V DC power supply and connecting it with a IMU thats cannot go higher than 1.9V on the I2C bus
I use 1.8V.
Will the I2C coomuncation...
Hi,
I have a new NRF5340-DK and I am trying to connect it via usb on linux but do not see it in the syslog when connected. I actually do not see anything at all.
When...
Hi,
I want to implement a pwm output signal on a particular pin of the nRF52840DK working with the latest nRF Connect for VS Code. What would be the recommended way to setup...
Hi,
I tried to flash the blinky example to an nRF52840 Dongle as described here:
https://academy.nordicsemi.com/flash-instructions-for-nrf52840-dongle/
Console output...
Hi I'm trying to create a transparent CDC to NUS bridge, this is based on the nrf52840 dongle.
The Aim of this is to send binary files to our device from a PC, our device...
I wrote a code for GPIO interrupt when DRDY pin goes high to low(Data ready) interrupt should occur and call a function but it is not working Below is a code:
intDRDY =...
Trying to implement FOTA DFU over BLE. My application uses my proprietary code (instead of mcumgr) to download signed OTA firmware image to secondary slot (in my case it is...
I am working on an application with significant constraints on power consumption and distance immunity. After some research, I found the Thingy:53 module, which is well-suited...
We had tried AT#XSLEEP=1 command in nRF SDK 2.5.0 and it worked. We saw it working for both modem FW 2.0.0 and 2.0.1.
When we updated SDK to 2.6.1 and modem FW 2.0.1, the...
I am building and running the Serial LTE application on a nrf9160. But am facing an issue with the application going into a reboot loop when network is activated.
I am using...
Hello,
I am working on building a BLE peripheral using the nRF52 DK board. I want to create both connectable advertisement and unconnectable advertisement (beacon type)...
Custom nRF9160 hardware. UART0 over RX/TX-TTL. Updated to MFW 1.3.6. nRF SDK 2.5.2.
Two issues:
1)
Normal at_client w/ PDN enabled to set APN. LTE Link Monitor, and...
Hi
I have a question regarding the power consumption of my own PCB.
I have taken a power profile of the nRF9160DK dev board and of my own PCB with the same software, but...
