Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hello,
We have been working on a Bluetooth Mesh application based on NCSv2.5.1 using nrf52840DKs for quite some time. We are now considering acquiring some DKs of the new...
Hello. The problems with starting advertising started after I wanted to add NVS (most likely). The error occurs in the bt_le_adv_start function
What does this error mean...
I am working on a project with the nRF9151 chip. In this chip, I am using the LTE modem in eDRX mode .
Apart from eDRX mode , I also want to put the MCU into sleep mode...
Hi,
I want to use the nRF53 with the timesync demo ( https://github.com/nordic-auko/nRF5-ble-timesync-demo ) to start an I2S task when a timer overflows on the net core...
Hello, The DevAcademy fundamentals lesson 6, example 1 shows how to connect a bme280 to a DK. Then in lesson 6, example 2 it shows how to connect to an onboard light sensor...
Dear Sirs,
I am writing you to inquire about following questions about nRF5340. Especially,regarding the configurable bitrate for the LC3 codec in nRF Connect SDK Ver2.8...
Hi
in my application, I need to reduce /disable RAM sections in nRF54L15 to save Idle RAM current. For Example, I need to retain only 64KB RAM when I am in idle.
how can...
Hi folks,
I'm attempting to program an nRF52833 using a Segger J-Link+ connected to the SWD program/debug pins on the board.The board is only an nRF52833 - as a learning...
hi, noted a few things in the Rev 1 Errata v0.8 that might be tricky to solve practically in sw/hw
3.16 [33] RADIO: GPIOs can exhibit radiated emissions
max...
I'm currently attempting to register a service and it's subsequent characteristics statically using variables and not hard coded GATT tabel , I can successfully register an...
Hello,
I've been playing with an nRF54L15 PDK, specifically with the sid_end_device sample. I was having a lot of trouble getting the device to register/connect to Sidewalk...
Dear,
We have project using normal advertisement (not extended) on a nrf5340 module (Raytac MDBT53-1M) to send data using Manufacturer data.
We have a product already...
Hi, Currently Im developing on a custom board that has a NRF52840 and a NRF9160. Both MCUs communicate using UART Async API and I added the support for LPUART on both sides...
Good day, I'm trying to use pin 1.02 as a GPIO in a TF-M build using a (custom) non-secure board target, and I'm struggling to find the appropriate way to accomplish this...