Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hi! I measure the micro frequency by Hantek Osiloskop in two-mode.
First, I use a simple Blink without softdevice , reaching 570kHz in 10us. Second, I use a ble_app_blinky...
Hi, I am looking for some help in interfacing STM32F4 MCU and nRF52832 module via UART for establishing BLE communication. My application needs both the devices.
I downloaded...
Hello everyone,
how can I implement a blacklist for my central which is scanning for a UUID and should also check for example device name. If the device name is in the blacklist...
We have developed a sensor application using ESB protocol with the nRF SDK (nRF52832 on Tx side and nRF52840 on Rx side).
We would like to redevelop now the receiver under...
Hi
1、I made the following modifications to the hello_world example（ncs1.7.0\v1.7.0\zephyr\samples\hello_world.
2、I have disabled uart0,But the average power...
Hi,
I'd want to implement RTC for regular testing of a variable. I am largely based on The BLE_uart exemple and have added a timer instance and a PWM instance. As the...
Hello,
I run a piece of code on NCS1.8.0 on nRF5340-DK, and it returns -35 when executing k_msgq_get()，b ut the same code runs on NCS1.5.0 and the k_msgq_get() function...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0).
Since I want to bond with Android, I have created a central code that summarizes the functions that I...
Hello everyone i am trying to integrate nRF Calendar example with the nRF5 Thread MQTTSN example. In my application, I will get the date and time source from the MQTT-SN JSON...
Hello,
I have a zephyr project built using NCS v1.8.0 with target board selected as nRF9160DK_nrf9160_ns. I am interfacing LSM6DSO sensor with nRF9160 dk, with interrupt...
Hello,
We have a firmware developed for Full Thread Device. But now as i want to reduce power consumption i want to convert FTD device firmware to SED firmware.
SDK...
After reading this https://devzone.nordicsemi.com/f/nordic-q-a/3830/what-is-the-value-of-the-gpio-pull-up-and-pull-down-resistor
and seeing that the internal pull-up is...
I'm trying to get readings from an LPS22HB sensor with the nrf52810 using the lps22hb driver in SDK 17.0.2_d674dde.
The lps22hb_init() call completes without any errors...
Hi, I'm using nRF52805 and SEGGER.
The firmware could be programmed to the chip successfully when I use Debug->go. I can connect with the BLE signal.
However, when I use...
Hi! I am struggling with figuring out how to properly set the sampling frequency for the qdec device. I noticed that making changes directly to the members of config struct...
