But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
https://devzone.nordicsemi.com/f/nordic-q-a/44658/communication-probl
I want to change the code provided in this link to enter the password from the peripheral
Hello,
I am using nRF Connect 2.5.2 with a Xiao Seeed BLE Sense nRF52840 and Jlink EDU mini
I am trying to flash the peripheral_hids_keyboard sample with Ozone, and I...
Hi everyone,
I'm trying to measure battery level using nRF52833. Reading previous posts, there are two popular ways to measure battery level with SAADC module 1) battery...
Dear All,
I need your help to clarify some LE Audio protocol related concepts.
For the BIS use cases. When the PC pause the playback, after that, are there any ISO packets...
The MCUboot, Slot0, and Slot1 flash partitions are defined in the board file. E.g., nrf52840dk_nrf52840.dts has boot_partition at 0 with length 0xC000, slot0_partition at...
OS: Windows 10
NCS: 2.4.2 We are evaluating adding the APDS9960 to our existing nRF52833 based application, but can not get the APDS9960 functioning. We are interfacing...
Hi,
in the PCB circuit I marked in the pictures, it seems that vias have been added to the marked areas on the pads of the nRF52840. However, PCB manufacturers say that...
Hi, I am relatively new to the Nordic platform and Zephyr RTOS. I am using nRF Connect SDK version 2.6.0 (the VS Code extension on Windows 11) with the nRF52840DK. I was wondering...
Hi,
I am designing a two Layer PCB with nRF52840 with PMIC, RTC, Flash. Can anyone from Nordic Review it? especially the RF antenna, I have used the Reference design from...
To verify my Custom antenna design on a PCB . AND VERIFY THE PCB.
https://cart.jlcpcb.com/quote/gerberviewThree/?qs=582f0d800a0c49398584815906f24877_1_0_1_0_0.html&_gl=1...
Hi
We are developing Zephyr projects which are compiling and working fine with Visual Studio Code running on a Windows PC.
Now we want to build the projects on a build...
Hello,
I am wondering where the best place to add a transport layer for DFU is? I have both bootloader examples working, but now i need to add the transport layers. On one...
I am implementing SPI communication between the intanRHD2132 (ADC) and nRF52840.
I need to periodically send commands (READ, WRITE, etc.) to the intanRHD2132 (ADC). To achieve...
Hello,
I am using the nRF52840 as modbus client and experiencing some missing bytes during communication (RTU mode) when using a high baud rate (460800). This tends to happen...
Hello, I have a question about how to get commands generated from a client cluster in a coordinator. I am currently developing a hub to control and retrieve data from home...
