But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
hello,
we are trying to use the stack guard module - obviously we want this to give well-behaved fault handling in the event that the stack gets too close for comfort. ...
Hi, I have a few questions regarding the modem module of the nRF9160 and considerations that might to be made when developing for it:
1. How does the modem determine which...
Hi,
We upgrade our SLM app from sdk 1.9.1 to sdk 2.0.0 and now when we try to look for GPS there is a reduction at the voltage from 3.3 to 2
what are we missing? what...
Hello Team,
This ticket is in continuation with Case ID: 292116. Based on last discussion I have taken more modem traces which are present in the attachment. Please ignore...
I've been working on porting a project to NCS using VS Code as my IDE. Now that NSC v2.0.0 is out, I wanted to move to that. I found the migration guide: https://developer...
I want to intercept some data in the RX (in section UART_RX_READY in uart_cb() as a command with arguments. And I do not want this data to be sent on the the BLE.
After...
I use nRF Connect to scan BLE devices. nRF Connect can find ANCS2 device. But nrfutil dfu ble failed with Exception: Connection Failure - Device not found! And I can't find...
When I run TX tests with the AT%XRFTEST command, I can start the TX test without any problem but then the modem stops responding to AT commands. For example, if I send
...
Hello.
We are currently using MBEDTLS to handle DIFFIE HELMAN and AES . We have disabled all unused curves and modules, as suggested in documentation. Still the size of...
Dear all, I am trying to develop an application on Nordic nrf52840_dongle utilizing Bluetooth and Nordic Led Button Service. The application running on the dongle is supposed...
I was starting to develop for our own board based on the nRF9160 where we will just be using the LTE-M and while doing so, ran into issues with enabling the LTE. To do a sanity...
Working on a BBC microbit v2 (nRF52833) with Zephyr, I can only control the "ring" pins of the microbit's edge connector. I can setup pullup or pulldown on the other pins...
Hello,
I am using the nrf52832 and would like to know the clock sources used by the external peripherals. From the searches, I found that PCLK16M is used for most of the...
I am working with STM32-F401Re with IKO1A2 shield on it as well. I implemented the machine learning core on LSM6DSOX and I get the data of that accelerometer on STM32 F401re...
Hi All!
I am using nrf5 SDK 17.0.1 and using a radio test example to extend the range of nrf52833/20. Able to compile the example for nrf52833(pca10100).
Now the issue...
