But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi community
I'm trying to build the nrf9160/http_update/application_update example but it keeps failing ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf...
Hi,
I would like to use MCUboot together with TF-M for an application running on nRF9160 in order to have the security features provided by TF-M while having upgrade capabilities...
Hey all Board: NRF53840 DK ERROR: Building ‘zephyr/zephyr_prebuilt.elf’ from solution ‘build’ in configuration ‘Common’ undefined reference to `LOG_DBG' (to any area that...
Hello,
We are in pre-production and we need to make 1000 prototypes.
Here is the filter we planned to use : https://www.johansontechnology.com/datasheets/2450FM07A0029...
Hi support team,
Customer needs them for BLE certification though I think those in nRF52840 report are same.
BTW, may I pre-fetch nRF5340's for any future request? ...
Hello,
Have any developers here on the forum had luck with getting the nRF9160 DK working in India?
Our India dev team has looked extensively and has not yet been able...
Hi, dear Nordic.
I tried to build secure_bootloader_ble_S132_pca10040 project in Segger. And it gives me this error message:
cannot find ../../../../../external/micro...
Hi,
I am trying to get my nrf24L01+ to communicate with nrf5340 using the enhanced shock burst sample code. In the sample code there are LOG_INF, LOG_ERR, LOG_DBG commands...
Hello Nordic Team,
We are in production phase, and flashing our modems one by one does not work well. It is too slow process, so we are looking for a solution that can offer...
Hi,
I'm trying to develop a Bluetooth Mesh Network using 3 Thingy52s and one Thingy91 that acts as a gateway to Azure IoT Hub. I saw the sample code LTE BLE Gateway for...
Hi,
I am trying to get the Atmel WINC1500 module to work with the nRF9160DK.
I have read a similar post,
https://devzone.nordicsemi.com/f/nordic-q-a/76640/spi-issue...
Hej!
I am trying to make a circuit / configure my SW for using the nRF5208 to have a small power consumption when not trainsceiving . Basically, I need my setup to have...
Hi! The nPM1100 is advertised specifically as a complementary product to the nRF52 and nRF53 product line. Seeing how the nRF9160 can also operate at 3V, I was wondering why...
