Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hello,
I am using the nRF54L15-DK development kit. The peripheral-uart example works well to stream data from the kit to a smartphone using the nRF-tools App. However...
I am trying to use the ADC on an nRF52840DK.
I have configured the two ADC channels in the overlay
I setup the channels like this
and take readings using this code...
Hi, I have faced dificulties calling zsock_poll for ZSOCK_POLLIN with multiple opened sockets, expecially when conbined TCP and UDP at the same time. My goal is it poll for...
So when I toggle the pin high, it gets set to 1.8V. I want it to be at least 2.8V. I did configure the VDD to 3.3V. The VDDIO does show 3.3V, but a pin like let say P1.11...
I have been trying to use the ` nrf\samples\bluetooth\peripheral_nfc_pairing ` sample code on the nRF Connect SDK v3.0.2 to connect to a Samsung Galaxy A16 5G phone.
The...
I bought a tiny board on Aliexpress from HolyIOT. It comes with an nRF52832 and an LIS2DH12 accelerometer. The silkscreen on the board says HOLYIOT-21011-v1.0.
This schematic...
Hello,
We are developing a board with both nrf91 and nrf54 boards. We are looking to make the nrf91 a SLM with a UART interface to support the LTE functionality of the nrf54...
Hi, I have two concerns about the functions nrf_gpiote_subscribe_set, nrf_gpiote_subscribe_clear, nrf_gpiote_publish_set, and nrf_gpiote_publish_clear. The expression
*...
Hello,
I'm trying to figure out why I get this warning that seems to block the compilation process but a bit of context first :
I'm resuming a project that was paused...
Hi,
I am trying to create a new board, following the Exercise 1 – Custom board for single-core SoC (nRF Connect SDK Intermediate), but I am getting this error:
Does...
Hi,
After I executed nrfjprog --rbp ALL , how can I unlock the chip so that I can program the board again?
Currently, the only way I can program it is by running the following...
Dear Nordic Devzone,
I have some questions regarding battery profiling procedures.
1. Is it normal for battery profiling to take longer than 8 days? As you can see in...
If i want gsm am uploading one file and if i want gps am uploading different file(SLM shell). Now I want both GPS and GSM to work in same file which needed to be uploaded
Hello
i have a design limitation for height in my product and i need to find another inductor with a max height of ~0.5mm can you please share more information regarding...
