This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I encountered an issue when using BT_LE_ADV_OPT_CODED in the bt_le_adv_param options.
When I enable BT_LE_ADV_OPT_CODED , the device cannot be scanned by other...
I am currently developing a project using an nRF5340DK and a custom board. ---------------------------------------------
PC ---(SWD)--- IntMCU at nRF5340DK ---(SWD)--- nRF5340...
Hi,
We are trying to get an accurate estimation of energy consumption of LTE searches and data sessions.
We currently do this based on XMODEMSLEEP and CSCON notifications...
I'm a bit confused about configuration necessary for PAwR where a connection is initiated with AUX_CONNECT_REQ as in examples periodic_adv_conn/periodic_sync_conn. If I disable...
Hi, I’m seeing a build failure after enabling SQSPI in the device tree when building with MCUBoot on NCS v3.2.1 for nRF54L15. The build works fine without SQSPI, but once...
Hello,
Did anyone get nrf54L15 to work with a TFT display over SPI?
I have been using the 1.28" 240x240 gc9a01 in several projects with nrf52840 (both using the DK...
Hello,
Recently I designed a wireless keyboard with a nRF52840 as the main processor. I had the board reviewed by a friend and had it produced by JLCPCB. I have assembled...
I'm currently attempting to profile a non-rechargeable lithium battery on nPM PowerUP(2.2.3). When I start the profiling process, the charging stage is correctly skipped,...
We've designed our own board based on nRF9160 for main CPU w/ LTE and an nRF52 for BLE. Using BMP for debugging.
I've successfully run several boards through the production...
hi,
i'm learning this exercise and i got this build error.
i'm using nrf 9160dk so can anyone tell me what problem am i facing in build time error.
thanks
vivek
Not sure if this is an nRF Connect or VS Code or Zephyr or West or some combination of the above, but I'd like to configure the development environment (nRF Connect extension...
Hello Nordic,
I am currently evaluating the nPM2100 using the nPM2100 Evaluation Kit for a low-power embedded device powered by a CR123A primary lithium battery (Li-MnO...
Hi,
I am testing an eSIM card. I am able to read the ICCID (20 digits) using the following command:
AT%XICCID %XICCID: 8934014012215261620 OK
However, I don’t know how...
This should be a simple answer. I had the nordic extension loaded on my dev machine for a while.. I have since deleted manually a few SDK (2.7 and the like) . I attempted...
