But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi all!
I'm currently working on the UART on the nRF5340 board. The SDK describes three options: -polling API,
-interrupt-driven API,
-asynchronous API. With Polling and Asynchronous...
During development I noticed the following behavior:
If NRF_SDH_BLE_GAP_DATA_LENGTH=251 and NRF_SDH_BLE_GATT_MAX_MTU_SIZE=185, on Android devices the connection procedure...
Hi
For some reasons my Windows 10 laptop reports two JLink CDC UART Ports when I connect one of my nRF52SDK boards.My plan is to use this board with nrf Sniffer / Wirshark...
Im struggling here with porting my code from SDK15 to NCS 2.0.2
Im happily TXing data from NRF52811 via UARTE and receiving via FTDI to PC, but Im unable to receive any...
Hello,
in the nrf connect application for mobile phone I can see the RSSI values being updated when scanning, but when I connect to my peripheral the RSSI info is not available...
Hello, I'm developing firmware for our custom board with a nRF9160.
The problem I'm having is that the modem crashes with error code 0x10 sometimes (read: about every 3rd...
HI guys I am working on nrf connect sdk v2.0.0, I am trying to modify periodic_adv example to stop changing mac address every time an advertising restart.
Hi,
I am writing the sample program "https_client" to the nRF9160-DK with Visual Studio Code's "Flash". I need to set the APN every time I write with Flash. Is it possible...
Hi,
When I'm trying to use LVGL along with Zephyr, I get the following:
I already tried to "play" with different CONFIG_MAIN_STACK_SIZE and CONFIG_IDLE_STACK_SIZE...
Hello Team Nordic,
We are using nrf9160 DK with nrf connect SDK 2.0.0 and mfw_nrf9160_1.3.2 modem firmware . In the Download_Client example we have changed the URL and the...
Based on the reference designs, the nRF52832 needs a 100pF decoupling capacitor on the DEC3 input. From my reading, this is a PSU decoupling capacitor, presumably for higher...
Our devices are provisioned via mesh shell, not over the air so we have to pass the IV index to the mesh provisioning command However, because the current IV index is not...
I was asked to create a windows application to get the device name and the signal strength of nearby modules with a nrf ble module.
The idea is to have an application the...
Hi,
I'd like to have a HW review. I have designed a PCB around the FSC-BT630 module which includes the nRF52832.
I have included all the files necessary for your to check...
