Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
I currently have an issue where by the Chip-Select is not toggled at all when configuring the csn pin to pin <18> on the Nrf52840 using Zephyr (version 2.7.1).
See dts configuration...
Hi All!
I am using NCS v2.0.0 and nrf52820 custom board and an example to test is radio test . I tested that example with nrf52833DK , code is executing/ printing messages...
Hi!
I'm developping a battery powered product, so the power consumption is important. I need to multiple an array point by point with an array (hamming window) that I store...
Hello support,
Your choice of 201 size component packages are not ideal for manufacturing (and HW debug). I understand some of the reasoning especially on 21540 antenna...
Hi,
I'm trying to implement zigbee into our application. For testing purposes I start with the example code, and I use the multiprotocol template as a starting point.
...
Hi
I am trying to migrate my project to newest NCS v2.0.0 but is struggling figuring out how to configure SPI2 slave operation mode.
The project is currently running v1...
Dear Nordic Team,
your chip above is on 52 weeks lead time, so here is the question:
a) I can spot inventory for the 8 channel version: nRF24AP2-8CHQ32 - would this...
Hi,
We are trying to add lwm2m (client) into light bulb sample (matter).
It results a redefinition of gethosname : CONFIG_LWM2M defines CONFIG_NET_SOCKETS_POSIX_NAMES...
Hi,
I have a nRF5340 DK (not the audio DK). I read the specification of nRF5340 Audio DK and found that it supports LC3 codec. However, I want to ask, is it possible to...
Hi,
I'm trying to measure the current consumption of the nRF9160 DK using a Nordic PPK 2 in various modes. Through reading up various documentation regarding this, I have...
I've installed nRF Connect and VSCode on a MacBook Air M1. Whenever I try to build my existing firmware that builds fine under Windows, I get the following error:
The terminal...
Hello together,
I have my own MAC addresses and want to make Zephyr use them. How can I do that?
What I found out is that the firmware read the MAC from settings "bt/id...
From everything I've read, I should be able to see log output in the "LTE Link Monitor" when logging is enabled. Instead, it appears to freeze up the LTE Link Monitor and...
Hi!
Currently, I'm trying to create a new board. I have a source code for the Thingy52 board and the code just compiles. With my own board I get __device_dts_ord_10 linker...
I have the direction_finding_connectionless_rx and direction_finding_connectionless_tx sample code running on a pair of nRF52833 development kits and the PCA20054 antenna...
