We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Dear Nordic Developer Zone,
Is there a way to set the LFCLK (32.768kHz) on a GPIO using nRF52811 ?
I want to use this clock for controlling another device.
Best reg...
I'm trying to implement OTA DFU in our custom App with our nRF52832 acting as the device to be upgraded. Everything seems to work OK in that:
1. New image uploads to the...
I have configured a composite USB device on nRF5340 with DFU+CDC+Audio interfaces and enabled MCUBoot. Trying to perform DFU using dfu-util tool on Windows always fails. Following...
Dear Nordic Engineers
I have a problem and would like to ask you about the frequency offset of NRF5340.
As we all know, if I would like to adjust the frequency offset...
Hi everyone,
I am currently working with NRF52833 and SDK 17.0. Everythings went pretty well, however, now i need to have some memory check in runtime since i used a lot...
Hi guys
I ve made a custom board using the nrf52811 SoC,and now i want to program it for testing.
The thing is i am really lost on what to do, this is the first time...
I wanted to use SES (6.32b) to build an example app (nRF5_SDK_14.2.0_17b948a, ble_app_blinky) and run it on a Nordic dev board (nRF52840 Development Kit), but crashed.
...
Hi there,
I just followed all the steps (twice) and I still cant get the welcome screen to show up. I cant get anything to show up when i click on create a new (anything...
I'm attempting to create and then update some NFC data to be presented as a type 2 device.
When I call nfc_t2t_payload_set it returns -45 (EDEADLK) but since the library...
We are using the DFU workflow available with nRF5 SDK 16.0.0 and nRF5 SDK 17.1.0 on our BLE devices. We have two different products, one using the nRF52832 and the other using...
If a manufacturer ships a large number of nRF52840 based devices that are configured as Zigbee end devices, and then later decides to switch them to Zigbee routers through...
I am using the Sparkfun thing plus nrf9160 feather with SDK 2.0.0 and modem firmware 1.3.2. Ultimately I would like to get LTE working along with GNSS, however, I can't even...
Good morning.
I am looking for an example of how to program the u-blox NINA-B221 module using the AT commands so that it is compatible with the application of the Nordic...
I've just updated from nRF Connect v1.9.1 to V2.0.0. In my bluetooth code that worked in the older version, I setup a couple of callbacks for BLE pairing:
In v2.0.0, I...
Hi, We are developing with the nrf9160dk as our development board. We are working from the aws-nrf-cloud a-gps sample (cat tracker sample) for our stack as our main system...
