We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hello all,
Four leds are connected to the GPIO (22-25) and gpio are defined and with a simple method within the while loop I can see them working
Next is to use the...
Hi, I am developing nRF52832, ADS1291.
I got the data from ADS1291 normally through SPI communication.
And I applied RTOS by referring to the nRF5_SDK_17.0.0/examples...
Hi,
Is there a way to turn off the reset loop detection on MFW 1.3? It's annoying having to wait half an hour when you are developing...
Kind regards,
Thomas
My product is devloping in nrf52810 with Zephyr . The flash is too small. At present, using all peripherals, the size of app_update.bin is 55KB. The size of MCUBoot partition...
Hi,
I'm a beginner, I want to do a test that will create a thread by "K_THREAD_DEFINE" marco.
Then I will continuous print "Hello~~~" per second. That's all.
But I don...
Hi everyone.
I'm approacing to the nrf52833 SoC following this official tutorial but when I import the example template the VSCode finds the cmake tool in my espressif ...
Hello,
SDK Version - 17.0.2
Mesh Version - 5.0.0
I'm using nRF52840 DK to build mesh example(light_lc_server & scene_client).
I try to save the scene of the...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1 I have two quick questions. 1) How to add version information(string) when make binary. 2) How can I read version when I finish...
Could you pls advise what control is there over the output voltage on PPK2?
For example, the STM power monitor only supports discrete output voltages such as 1.8V, 2.4V...
Dear Support Team,
I'm trying to test 802.15.4 feature with the precompiled radio_test hex file, but got an error when connecting the CLI through PuTTY. Below is the detail...
I am very new to the Nordic line and I have an nRF5340-DK that I would like to build a basic BLE Remote Control project. The Remote Control must pair with a phone or computer...
Hi,
I am using VS code for my project, which is using bl653 board. While in build configuration setup in vs code am getting this error. ERROR: source directory - does not...
Trying to add UART capability (sample project from console) to a a ESB transmit sample project. Could not get a build assert to work.
1) Tried to add all of the selections...
