This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm working on KX132-1211 accelerometer with nRF52832 and am using I2C(TWI) protocol. For that I need to create driver files even I was contact with manufactural...
Hi Friend,
We have a project using SDK16 and softdevice S140. We want to generate a looping output of 60ms 2.4GHz OOK and 500ms BLE scan. Ported 2.4GHz OOK from radio_test...
Hi, I'm Leo.
These days I'm learning BLE.
First, I'm using nRF Connect SDK(NCS) v1.9.1, S140, nRF52840 DK board.
I need to use SPI to control UWB transceiver(DWM3000...
Hello,
We've a design/arch question about the performance of nRF52840 device (dongle/EVK).
In our system, we've a PC connected to a PTX that communicates with multiple...
Hello,
I am working on BLE Mesh using SDK nrf5_SDK_for_Mesh_v5.0.0. I am using light_switch example for BLE Mesh client and server. I am using custom hardware for Mesh client...
I just finished successfully running the azure_fota and azure_iot_hub demos on my nRF9160DK. In a completely separate project, I am now attempting to adapt the TMP116 sensor...
Hi,
We're using Nordic Connect SDK V1.8.0 & nrf 52833 chip integrated on BL653 hardware & have some queries regarding logging SDK related data, following queries
What...
With an earlier version of NCS I could set the sda and scl pins using an overlay file:
boards/nrf52840dk_nrf52840.overlay:
With NCS 1.9.99 I get this error:
...
Hi,
I'm using the nRF52840 on a custom board along with an ESP8266 (ESP-12S) Wi-Fi module.
The ESP module prints out a bunch of information at a weird nonstandard baud...
I am having trouble setting up DFU over BLE in nRF Connect SDK. I am using NCS 1.9.1. I have followed these instructions with my own project on both the nrf52840 devkit and...
Dear All,
We are developing a device based around nRF52840 on a rigid-flex custom PCB that is mounted inside an anodized aluminum cube with one face covered with plastic...
Hello, I'm trying to get an LPN to unprovision itself based off of an external command. I tried to base it off of the examples so I simply call: However after the reset it...
Hi,
I have my device based on the nRF52840, we have manufactured some equipments and we have created our own application to manage connection. Everything is working fine...
Hi all,
we recently had a problem with couple of our boards based on Raytac MDBT50Q-1MV2 (nrf52840 + osc. + antenna). We base our app on Zephyr. After programming some boards...
