But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hello Nordic Team,
I'm developing a project with two nRF52/nRF54 microcontrollers where I need: - 1st microcontroller as BLE peripheral receiving mobile app data (nRF connect...
I'm migrating code from ncs 2.7 to 2.9.
I am using CONFIG_BT_EXT_ADV and scan timeout callback - such timeout requires CONFIG_BT_EXT_ADV:
It was working fine. Now it's...
Hi,
I follow the custom board exercise steps with mynRF52840 DK and when I reach step 8.1 , in the deviceTree visual editor, I notice that the GPIO0/1/TE options under ...
Hi, I recently updated from NCS 2.6.0 to NCS 2.9.0 which had lots of changes. I believe I ported from child_image to sysbuild with success, as my main application on app core...
Nordic has changed the API of nrfx nrf_modem_dect_phy from SDK 2.7 to SDK v2.9.
In struct nrf_modem_dect_phy_callbacks there is an additional callback member stf_cover_seq_control...
Hi Team,
As mentioned in the datasheet of nRF9151, Imcuoff0 mode (MCU off, modem off, wake on GPIO and reset) consumes around 1.4 uA over VDD power supply then what is the...
Hi ,
IDE: SES
NCS version: 1.9.1
I install the development enviroment following this article. 开发你的第一个nRF Connect SDK(NCS)/Zephyr应用程序 - iini - 博客园 (cnblogs.com)
I use...
Hello,
I am trying to find a solution how to use wifi and ble on thingy91x and manage the coexistence between them, I have found a sample Wi-Fi: Bluetooth LE coexistence...
I am trying to implement the following: I have a mesh node built using the Sensor Server example for publishing temperature data. I want one relay node to transmit the temperature...
Hello All I'm new to the forum so please be gentle! I hope this is ok to ask: I'm in the early stages of planning a project that I hope will be suited to a DECT NR+ platform...
hello!
I'm currently looking for a way to access the nor flash of the nRF7002DK, does anyone have an example of this? My goal is to write, read and erase data to the nor...
Hi,
We are starting our first production run. I have studied earlier assigning IMEIs and how to obtain IMEI numbers via Nordic semiconductor up to 100k devices.
We planned...
Is it possible to get access the virtual com port from an application based on nRF5-SDK-for-Thread-and-Zigbee?
My application requires nothing more than the LED and the...
Hi.
Base On Nrf52840DK , SDK V2.8 and Zephyr
Can't See CTS service when connected to nrf connect (Android App) and source code is "peripheral_cts_client" , Why ?
