But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I made a PCB board, but I couldn't connect to the chip with JLink. I used a lithium battery to power VDDH. I want to test if there is any problem with the hardware. I tried...
I am using NRF5340 with NRF connect (Zephyr) and logging out to RTT (printk or printf, etc) , which works but sometimes I get buffered fragments and dont see the rest of the...
Product: nRF54L15, SDK:3.0.2, door lock application
Hi,
When the Matter door lock removed from Apple Home(Home App, remove accessory), the lock does not remove all the...
Hello,
I am experiencing an issue when trying to flash any program using nRF Connect for VS Code. When I execute the flash command, my board disappears from the "Connected...
Hello,
Is there support for fuel gauge algorithm with the CR2450 and the nPM2100 implemented? If not, is there a plan to release support for it soon?
Thank you,
Fin...
Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Hello,
I have been trying to get my brand new nRF52840 Dongle working as an 802.15.4/Zigbee sniffer, but I am not able to capture any packets, even though the interface...
I compared the S132 and S140 protocol stack files. The S132 file does not occupy the 0x26000 address, while the S140 does occupy the 0x27000 address. However, the application...
Hi, I've spent a few hours trying to figure out a way to use the onboard PDM microphone on Thingy52 with the nRF Connect SDK.
I saw a pull request for one from a member...
Hi nordic:
I am using NCS 3.0.0 and VSCode. I was able to compile the sample code in the SDK some time ago, but now I am getting the following error when compiling the sample...
None of the buttons work, most errors are similar to as follows but specific to each button:
Error running command nrf-connect.app.createBuild: Could not find SOC. This...
Dear nrf team,
We are facing an issue with the eSIM on our nRF9151 board. The SIM 1.8V pin on the nRF9151 is not supplying 1.8V. We have checked this using a multimeter...
When trying to flash the NRF Bootloader via OpenOCD, i got this error from command line:
nRF52 device has a CTRL-AP dedicated to recover the device from AP lock. A high...
Hi team,
We are evaluating Amazon Sidewalk from Sidewalk SDK v1.0.1 , the hello-sidewalk sample is ported onto our in-house prototype board (nRF54L15). We’ve:
Provisioned...
