i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hi,
I am developing application on NRF52840 with Zepyr 2.1.2 SDK, and I found two problems when using the example scan_adv, as follows:
Executing bt_le_scan_start in...
My team is developing for an nrf52840 on a custom design pre-production PCBA. Up till now we have been using nrf52840dk_nrf52840 in the"Board" field of the "Add Build Configuration...
Hi Team We’re using Nordic connect sdk 1.9.1 We’ve created a vendor service and defined multiple characteristics in same, We are using Nrf connect mobile app to fetch the...
Hi,
I am trying to capture provision packets from the BLE Mesh. I have nRF app for iOS. My iPhone is considered as a provision device, is it possible to provison another...
We are using SDK v1.9.1 with VS Code to develop software for a custom BLE board using the nrf5340 SoC. We also have/use a nrf5340-DK development board.
We generally update...
I want to make a card according to the NTAG213 specification package of NXP.
After I set the parameters, the default value for reading the card content will be NTAG203...
Hi,
We are running Zephyr 2.4 via PlatformIO on a nRF52840 based product. While spamming the nRF with a ton of BLE packets, after about 15 minutes or so we get the following...
Hi,
I have quite demanding SPI device which should send its data over BLE. Thanks to throughput example i was able to achieve maximum transfer speeds for synthetic tests...
Here are some values I got from the terminal:
11011110000000000001000000000010
00000010000001010000010000000011
00000011000000010000001011011110
I do not see the sign...
Good morning,
To my knowledge, the nRF52833 dk as well as the reference designs are FCC certified.
I'm currently searching the FCC IDs for these designs but I'm not able...
Hi
Using nRF52DK + SDK17.1 + S112
I have retarget enabled & using printf to output over UART (no DMA)
What's the best way to check if printf is busy outputting data...
Hi ,
What I am trying:-
-connect the custom board with nrf52840 chip using nrf52 dongle on pc with python.
-Already set some commands on custom board so when my pc ...
Hi:
i use the application note nA34's python file (dtm.py) to perform DTM PER test among 2 nRf52840 DK.
and in the LE_Test_Setup command ( the only set command which upper...
Hello,
Every time I try to run the sample gnss in SDK 1.8, I got this error gnss_sample: Failed to generate JWT, error: -8
Please can you let me what this error means...
In my application, we do not expect Centrals to have persistent relationships with Peripherals. We don't need them to store information about each other. However, we do need...
