After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi,
I am working on a project in nrf connect sdk v2.0.1 central side using nrf9160dk_52840. I want to pair my peripheral device with this central That is possible. Please...
Hi,
I am beginner with NRF52840. I want to create a task scheduler using multiple tasks with different level of priorities that is low, medium and high. I am using SDK...
Hello,
I got two PCA10056 1.0.0 DKs equipped with an nRF52840 rev. 1 (code AC0). Both do not measure the VCCH voltage correctly (displayed voltage ~2.4V instead of 3.0V...
This forum feels pretty advanced, so if this is the wrong place to ask this question apologies and please let me know where I should be asking it instead.
My goal is to...
Hi,
I'm developing on the current setup:
nRF52833 DK, emulating an nRF52820.
Soft Device 113 version 7.2.0
SDK 17.1.0, with updated MDK (see link )
IAR EW ARM...
Hi Everybody,
I need help in writing a little software on NRF52805 which will active the transmitter with parameters:
1) Frequency : 2402Mhz only. (and i will later...
Hi,
I'm using nRF52832 with S140 v7.2.0 base on nRF5_SDK_17.1.0. I use PCA10100 development kit and set VDDH/5 as input and use internal reference (0.6 V) to do the battery...
Hi
I am working on SPI implementation on BL653_dvk board and while SPI_transfer i want to capture the timeout error.
but not able to differentiate which timeout is correct...
Hello,
We are using MDBT42Q-512KV2 module which is based on nrf52832. There is Central and peripheral ( Foot Pedal Switch ) using same module.
We have used crystal from...
I know from the product specification for the nRF52832 chip that the high frequency clk can use a external 32 MHz crystal as source. My question is, is it possible to supply...
Hello!
I am now developing a product with NFC based on nrf52833.
I need to transmit some crucial data between device and phone, such as device settings.
But I have...
Hi all,
I would like to measure time intervals between gpio edges along with Matter.
I tried to use a 100us timer interrupt but seems it will crash the original matter...
Dear Support
I have made the following findings of my evaluation of the NRF5340 with Version 2.1.0 SDK:
-CIS mode has no constant delay at default settings 48-4. According...
Hello Nordic team,
I have looked at the BLE + Zigbee multiprotocol examples from nRF5 SDK and in these examples, I see that there is a file ' multiprotocol_802154_config...
Hello,
are NRF SoCs considered as BLE certified?
What is the default firmware in such case?
I guess no fw changes are allowed so that certification remains valid, right...
