Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
We want to start with ble_app_uart example for our product but it the firmware halts at CRITICAL_REGION_EXIT() in nrf_sdh_enable_request.
We are using the example from 17...
Hiii, is there any libraries or example to read nfc tag through clrc663 nfc reader, could any one direct me to the any solution
thanx in advance
suprith
I am having problems setting up UART communication between nrf9160 and nrf52840 on Thingy91. My set up consist of a Thingy52 and a Thingy91. I am using ncs version 2.0.1....
Hi,
I've been working on Open Thread recently. I found that after I send provisioning request, even though there are 3 servers "enabled provisioning", the callback function...
Hi,
I am trying to setup a raspberry pi 0-W for flashing nrf devices. But nrfjprog doesn't seems to work.
I am using Raspberry Pi OS (32-bit).
I have fetched Segger...
Hello everyone,
I've got a simple question here today. I'm making use of the nRFCloud on our nRF9160-based system.
When using the different APIs to nRFCloud, be it location...
Hello team,
I am having a problem running LWm2m sample out of the box on Thingy91 (SDK 2.1.0, programmer 3.0.4). If I enable any of the sensors using something like the...
hi Team,
i am using Microsoft Windows 10 Enterprise OS and segger 5.40.
i am using nrf52840 DK device in my project.
i downloaded nrf connect for desktop software and...
Hiii team,
I am using the nrf52840 DK I want to connect the slave to the master How to connect a slave with out using a dedicated spi or i2c by using the simple GPIO pins...
American Semi produced this Silicon on Polymer IC a little while ago
Interested if anyone knows of this being used in a small form factor module
Seems as if they must...
Hi, We are starting to work on a production tester which will need to program a DUT based on the nRF5340. Both cores will need to be programmed and an external QSPIFLASH memory...
I've put the recommended circuit for the nRF52810 QCAA chip together on breadboard (schematic is below) and am using a J-Link Edu Mini to program.
I created a custom board...
When using Segger Embedded Studio, multiple build targets can be defined. Each build definition can have its own "defines", libraries, etc.
When using Visual Studio Code...
Mesh SDK 5.0, SoftDevice S140 v7.2.0, NRF52840, SEGGER ------------------------------------------------------------------------------------ Hello! I have a similar problem...
