Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello
I need to setup TLS communication using UDP, betwen:
- zephyr app as client
- ubuntu pc, openssl server as server (ofc)
I modify prj.conf of sample disabling...
Hello all!
I coming across a strange problem, the emStudio does not want to accept the nrf_log_frontend file not matter the file is in the folder, under the sdk folders...
Hi,
I have built and tested the CLI sample project on nRF52840 DK as well as a custom module. Now I want to extract the parts used for thread commissioning from it. I tried...
Hi, I'm trying to port my NRF SDK15.3 application to NRF Connect. I made a custom board for my PCB and I can control the LEDs with PWM etc. Now I'd like to read data from...
Hi,
I have a custom pcb with NRF52840-QIAA-F-R (rev3) on it. And when I tried to program it first time, nrfjprog shown the folowing error:
ERROR: The operation attempted...
In the mesh serial example, I found that the sequence number isn't stored into persistent flash. If that is the case, if the board is power cycled, no one can communicate...
Hi,
I am doing "application update" using AWS FOTA with presigned URL.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.0.1/nrf/samples/nrf9160/aws_fota/README.html...
Hi,
I'm planning to develop a product that takes an image via a cmos sensor, processes it and sends it via BLE. I'm using nrf5340.
What should I learn to build this product...
Hello there! I've been developing a custom device with a nRF52840 dongle. For this I had to develop a custom cluster to properly support the type of data I wanted the device...
I want to use the nrF9160 for HTTPS communication to access a server.
To do so, we need a client certificate.
is it possible to incorporate a client certificate into the...
Hi all!
I am developing an application with Zephyr (commit b21a91e46833cfcf4f2bda9e3e0f9d8c2150882e) on nrf52833 and a Ublox SARA R5. I communicate with the module via the...
The goal is to push a blob to a azure storage container using https on nRF9160.
I am using the nRF/zephyr socket library to do basic HTTPS POST/PUT
CONFIG_NET_SOCKETS_OFFLOAD_TLS...
Hi.
I'm trying to flash a sample image to the Thingy 53 using the nRF9160DK (assuming this is possible and it's not mandatory to use the nRF5340DK), but when I try to do...
Hi,
I am trying to run the peripheral_uart service example, with the hci_rpmsg on the network core
When the clock configuration (on the main application core) is set...
I use iOS nRF Connect APP to do nRF52832 device DFU. DFU is completed successfully. But the following error occur.
<error> app: Received a fault! id: 0x00004002, pc: 0x00000000...
