This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello! Lately we are testing FOTA functionality in our products. FOTA works well when the distance, between the ED (our device under test) and the coordinator, is short, but...
what can be the starting Point for Bachelor Thesis involving BLE 5.0 devices to be deploy in mesh Network. How the challanges in the Thesis can be address and set as a Goal...
I want to understand the ROM layout and set the memory map.
Please tell me how to know the layout of the current ROM. (Mainly the range used by MBR area and FDS area)
...
Hi!
I use ncs v1.3.0 and mfw 1.2.0 on a nRF9160 DK v0.8.5.
My app runs in PSM mode alternating between LTE and GPS following Jan-Tores suggestions in his response to my...
LTE Link Monitor doesn't seem to be able to detect any serial interfaces on macOS that are not the DKs (or don't have 3 serial ports)
See this hacky implementation: https...
Hi,
I am using NRF24L01 with arduino using RF24 library ( https://github.com/maniacbug/RF24 ).
While executing the transmission code i have observed the following line...
Hello dear!
This is my first post righ here. Hope you can clear my doubt.
I'd like to know if the CTE and IQ sampling features are accessible using the BLE MESH?
I'll...
Hello,
I have a device which sends a provisioning request to two other devices in a Thread network. They both receive the request and both send a provisioning response,...
Hello. I am testing the Secure DFU for NRF51 with softdevice S130 provided in the SDK Version 12. 3.0 following the steps in this guide. https://devzone.nordicsemi.com/nordic...
Hello!
I have a custom board with nRF52810 and s132. BLE connection is secured with passcode. it works.
I would like to get exact passcode entered by User if the passcode...
Hi support team.
My project build using keil IDE working stable. But when I change to build using makefile, although build success with hex file output and and everything...
Hi Team,
I have gone through many threads on the forum but still in doubt regarding how to interface nrf52 over HCI to the Linux based host.
My understanding is currently...
When building example ble_app_interactive_s132_pca10040, SES asks for missing "nfc_t2t_lib.c" and "nfc_t2t_lib_al.c" files. This happens when SES is 'Preparing target for...
Hi,
I'm currently trying to use 2 channel SAADC to measure 2 analog input port
I've searched other questions in this forum and referred SDK example
Actually, I could...
Hi All,
I want to measure the battery level in my nRF52840 design using the ADC.
I came across this thread in the nordic devZone https://devzone.nordicsemi.com/nordic...