Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi! I am trying to use the LE Audio application and one of the samples in it, by including the necessary source files, and Kconfigs in my project. On the network core, I am...
As per the doc , when I use a smartphone (the base version is Android 12) to touch the NFC antenna, I should see a pop-up window:
3.Confirm pairing with ‘Nordic_HIDS_keyboard...
Is it possible to promote my project here: complete Zephyr development environment running solely on Raspberry Pi 4 Bookworm OS? If nothing else it does provide information...
Hi There,
During the transmission and reception performance test, I found that the LE1M's maximum sensitivity was only -92 dBm, while the LE2M's maximum sensitivity was...
Hi,
we have a Gateway board that uses the nRF52832 with the nRF21540.
The firmware running on the nRF52832 is a slightly modified version of the HCI UART sample found...
I have a problem with timer 3 of nrf52820.
It concerns a trailing edge dimmer implementation based on timer 3. A gpiote is used to sync the zero crossing.
I use ppi...
Dear Nordic-Team,
I designed a custom PCB using the nRF9151 as the host processor, the nRF7002 as a Wi-Fi companion, and the nPM1300 as the power management IC. The Wi-Fi...
Hello,
I encountered a strange behaviour on a nrf52832 : - I flash a a debug firmware (with debug optim in build config) : I can run debugger and add breakpoints - I stop...
I am developing an application that uses NCS2.8.0.
For FW updates, the nRF52833 USB ACM bootloader is enabled.
However, there are some problem.
My device has a battery...
Hi all hope you all are fine and doing well.
I am trying to use the Soft UART (uart-bitbang.c driver) on nRF52 DK for a low-speed UART connection. The initialization fails...
Hello, I am not sure if this is the most appropriate place to ask this question, but any comments are welcomed. I am developming a sensor platform that tries to use extended...
So hello everyone, I am a computer science student with zero IoT background. I am trying to a wearable device . I want to nrf52840DK with max30102 heart rate sensor and communicating...
Using nRF5 SDK 14.0.0 with Softdevice s132 v5.0.0 on nRF52832.
I've set up my nrf to be a GATT client (in central role), and I'm using bluez on my Linux desktop with a...
Hi,
we have a NRF52832 based project / product. We are using a DFU bootloader for application and SD update. The update is done from a master microcontroller using UART...
Hi Devzone,
Currently, we are attempting to use the Generic three-wire coexistence (refer link: https://docs.nordicsemi.com/bundle/ncs-2.9.2/page/nrf/app_dev/device_guides...
