Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello,
I recently installed the nRF Connect extension for VS Code on my Mac M1. I am unable to see my connected board as part of the nRF Connect extension.
Setup
...
Hi,
I see that the latest Nordic SDK ( v17.1.0) supports mbed TLS version of 2.16.10 only. However, we have received a End of life notification for the same ( Mbed TLS...
Dear All
Could you point me a timer example, can be used to time the interval in ms between something? like read the system time when something happens and then read again...
Is there a way to find you the reason for RRC Connect?
I'm using a simple software developed based on NCS AWS IoT sample. I've implemented the SW to test power consumption...
Hi,
I need to configure an nRF52832 to wake up periodically from SYSTEM_ON and SYSTEM_OFF and, also, when a GPIO pin changes.
Where can I find sample code and docs for...
Hi Nordic experts,
i figure out how to add the end-point-out to the BLE HID EXAMPLE and i cheched it out on linux ubuntu and on windows 10.
It seems to work correctly...
For my Thingy91 project I need to hook into a variety of hardware interfaces including I2C. I am struggling to relate the pins https://infocenter.nordicsemi.com/topic/ug_thingy91...
Hello,
I'm using the nRF Connect SDK 1.9.1 and I have defined a custom board with nRF52840. This works for normal code (samples, etc).
The .dst has the following structure...
Hi,
Im using PCA10056 nrf52840 to measure light intensity with photodetector.
I got that sensor to measure the intensity of the light on the Arduino. But I don't know...
Hi all,
I have a problem when I try to debug nRF52832 target. The nRF52832 chip is advertising properly but as soon as I enter in debug mode, advertising stops. There is...
We got a project that is using custom boards and custom libraries that is able to compile for one board and that output strange errors for an other. Following is the prj.conf...
Summary: Not able to see messages from printf() statements in the code on the serial monitor.
I'm new to Nordic platform and to Segger Embedded Studio.
I have a Nordic...
Hello,
could you please tell me how to configure the Hardware Chip Select Funtionality for SPIM3. I am developing a communication between a sensor and the NRF via SPI transfers...
Hello everyone,
I am currently using NRF5340dk and I need the Library queue, (I especially need the functions: nrf_queue_push and nrf_queue_pop..). (Knowing also that I...
Hi Nordic Team, I am trying to develop an AOA application using the NRF52833 nordic SOC. I am using NCS 1.6.1 development SDK in Segger Embedded Studio.
I am flashing a...
