Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi,
I'm running into a frustrating issue where I can get the NRFX_SPIM and my own BSP examples to work, but when I try to combine them - the buttons stop triggering their...
I have an existing system for my elderly mother based on a nRF52832 puck ( www.espruino.com/Puck.js ) that includes the button-press-count in its advertising data. When the...
Hello,
we want to communicate the BLE to BLE without connection how to communicate?
One BLE is continious on scaning mode and another one is advertising mode on event...
Tried to compile the Bluetooth: Peripheral UART-sample, (nRF Connect SDK v1.9.1) and got an error:
FATAL ERROR: command exited with status 1: 'c:\ncs\v1.9.1\toolchain\opt...
Hi,
I am devloping base on azure_fota example and got the Peer closed connection! after used the SAS URL.
First, I complete do the FOTA by using the normal URL from blob...
I am working on my nrf52810 . I just found an issue that, when my device enter DFU mode its show dfu trag , I can not return to the application(If I do not want to upload...
Hi,
1. Is bootloader file and firmware file, different for projects build on nCS..? Or a single executable build file consists both bootloader & firmware..?
2. Can you...
Hi
I am working on driver for SPIS and would like to run higher than 8 MHz. We have been doing some tests and seems like it is possible to go e.g. 10 MHz.
Is the nrf51810_PS...
Hi,
How can I put an application at a specific memory location?
I want to upload 2 programs to my device and switch between these applications. I modified the bootloader...
Olfox recently raised a concern with the 400kHz frequency setting for the TWIM peripheral, which I confirm is incorrect in the SDK (17) and nRF52832 datasheet (v1.7); I attempted...
As described in that PR I am getting a hard fault when trying to cancel a download.
https://github.com/nrfconnect/sdk-nrf/pull/6955
To reproduce this issue apply the...
Hello! We are developing a board with NB-IoT connection base on the nRF9160 but also BLE capabilities based on the nRF52832. While researching the best way to implement this...
What is the default path of Kconfig in SES Project ? I testing Azure-Iot_Hub sample project. I define the AZURE_IOT_HUB_DEVICE_ID and AZURE_IOT_HUB_NAME in prj.conf file....
TLDR; How do I access GPIO and other peripherals via SEGGER IDE without using Zephyr when creating a new project as "New > New Project > Nordic A C/C++ Executable". Please...
Hi,
We are building an application on the nrf5340 application core. We noticed that library calls are being made to perform double precision floating point arithmetic which...
