Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
hi
I am using nRF52832.i have added 3 service and and 3 characterastics to one service
1.Peripheral service (accelormeter + gyroscope sensor) and 3 characterstics
2...
Hi, Nordic team. I'm planning to create an iOS 11 BLE app.
I want to create a BLE app that can approximately depict indoor locations after the iOS device scans BLE beacons...
Hello,
I am thinking of using Thingy52 for my project. Before I order Thingy52, I would like to make sure if it will workout for my project.
(1) I wonder if data collected...
I am experimenting with light_switch server example from mesh SDK 2.1.1 . I want to add UART functionality to this example.
I referred to the ble_app_uart example from sdk15...
after cmake -G Ninja ..
-- SDK_ROOT=C:/BLE/SDK/nrf5_SDK_for_Mesh_v2.2.0_src/../nRF5_SDK_15.0.0_a53641a --- set with command line ARG -- PC-Lint executable not found. Linting...
Hi ~ SDK: nrf5_SDK_for_Mesh_v2_0_1 's ligth switch proxy client & proxy server IDEs : SEGGER Embedded Studio for ARM Release 3.40 Build 2018052200.36079 Windows x64 SoftDevices...
I'm looking for the nRF5x SDK v14.2.0-SR3 tha is written on the Smart Remote 3 for nRF52 user's manual. I could not find it on the DevZone, https://developer.nordicsemi.com...
Hi,
I am developing software supporting LEsecure using SDK 12.3 with nRF 51822.
Please tell me what to do when incorrect data is entered in "Passkey entry".
Currently...
Hi.
I've been trying to send a payload with STM32F but I can not. I've used both STM32F103 and STM32F3 to send a payload but neither of them worked. However, when I use...
Hi,
I use nRF5 SDK v15.0.0. In my application I need periodically disable and enable Bluetooth because they are wifi also, which connected to the same antenna. Its mean...
Hi,
I'm trying send me the mac address of the device by UART by the following method:
By serial I receive:
Start b9:24:82:d5:4f:81
The problem its that the device...
Good day
Firstly, an overview.
I am currently busy with a technical proposal for a client. Initial details will result in a completed approx 60 000+ sensor network. My...
Hi EveryBody!
I've begin to work with the n51 family, my board is based on a n51822QFAA H1 IC.
I use Keil5 MDK and a ST-Link V2 programmer. They work fine as I've tested...
IOS, nRF Toolbox 4.4.4, DFU Library version 4.1.1
Attempting to flash to ruuvi with nRF52832 reports
:INFO:Hash failure and
:INFO:Return false in CRC
to J-Link RTT...
Hi,
I'm trying to modify the slave latency and supervisory timeout setting, but found sometimes the gap_params_init() will get error after changing.
For example, I can...
