Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hi all,
I'm currently working with the nRF52 DK (nRF52832_xxAA_REV3) using the nRF5 SDK version 17.1.0_ddde560 and the IAR Embedded Workbench - Arm 8.32.3 IDE. I'm facing...
Hi Team,
I just want clarity on 2 points related to accuracy of nRF9151 GPS.
1) As shown in datasheet, "Positioning accuracy (CEP50), periodic tracking" is 3.4m. So that...
Description: I am encountering an issue while testing the watchdog functionality. When I intentionally hang the system for longer than the configured watchdog timeout period...
Hello,
I'm new to software development so apologies if this is a simple question but I can't find a straightforward answer for nordic connect sdk on vs code.
An IC I...
How can i configure the nrf52840 dongle with DHT-11 sensor such that i am able to use it to send the temperature data via UDP within the Thread Network? I am using the NRF52840...
Hello, I have used this template (ncs-example-application) to start developing my project. I've installed also all the prerequiries to use the application using command line...
I am using the existing nRF Connect SDK (v2.9.0) example of Wi-Fi provisioning using Bluetooth LE ( https://github.com/nrfconnect/sdk-nrf/tree/main/samples/wifi/provisioning...
Hello,
I am currently testing a custom board using the nRF5340QKAA .
Most of the connections are the same as the nRF5340 DK , but the main difference is that I built the...
I dont have Ellisys, but I already install Ellisys Bluetooth Analyzer on my PC.
I got a .btt file in this ticket , but it seems something wrong.
I want some .btt files...
I am using an nRF52840 processor within a Particle Argon IoT module. I am polling a third party BLE peripheral (Shelly relay) for status data once a minute. The data packet...
when i try to use the ddfs to calculate the distance, i can't understand the comments in the README file,
"Zero-distance calibration
*************************
The...
I have followed the guide at https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu .
(using the option CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
After the Matter device is upgraded from version 1.1 to 1.3 via OTA, the Thread connection is functioning normally., but it fails to process chip-tool commands, and chip-tool...
I'm interested in connecting a device to a combination of RAK4631 and RAK5802 using RS485 interface.
I write the code in the Zephyr environment and I cant seem to make it...
