i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Im trying to make a simpel project reading the sensor BME280 over SPI. I can´t get any activity on the SPI pins when i check with my logic analyzer.
I´m using nrf9160-DK...
I've based my code upon the HIDS keyboard example and added code to support an attached polled sensor with I2C interface. The device will pair with the Android phone just...
Hello,
I'm writing an application that sends cycling power information via ANT+ and Bluetooth (S340, on a nRF82840). While the ANT+ is a pure cycling power service, the...
Hello,
I am using the Nordic SDK at v1.5.0, to create an application that runs on the Nordic nRF9160.
In the typical use case scenario, my application is mains powered...
Hello. 'm trying to DFU using serial bootloader with my custom board.
I've wired my custom board's nrf52833 pin with a USB2UART board.
nrf52833 RX Pin: P1.02 -- connected...
We have a device based on NRF52832, SDK 13.0, Softdevice S132 v4.0.5. We can't upgrade the Softdevice at this time but we can modify the firmware if necessary.
We know that...
My current product uses an NRF52832 with SDK 13.0 and s132_nrf52_4.0.5
I was asked to implement GATT caching to speed up the connection time with a mobile phone.
I know...
Dear ALL,
In nrf connect sdk ，How can I do a bond_ Deleted callback？At present, I test this function in iPhone and Android OS. When I delete the pairing information of...
I am developing my ADC sampling code for minimal power consumption. There is a timer with ppi module that generates interrupt for sampling. Please see the code below:
...
Hi everyone,
I'm designing with nRF9160, and I found nordic's suggestion on the PCB layer, which is underneath the GPS and LTE pad should be removed. I'm curious if the...
Hi.
I use GPS with SUPL client library, so I need your help.
I enabled CONFIG_AGPS_SRC_SUPL and use gps_agps_request() function to request agps
I found that in supl_start...
Since update 3.9.0, I am not seeing my Dev Kits or J-links showing up in the "Select Device" device list.
I have tried both Mac and Windows.
Anyone else experiencing the...
Hello, I'm new to zephyr
I have a custom board nrf52833 (BM833E module), I'm using zepyhr to build the hello world example to use uart1. I have created nrf52833dk_nrf52833...
Hi.
I'd like to develop my custom board's DFU function like the below steps.
Run my application (simple LTE transfer function included)
During LTE transferring, If...
Hello,
I want to make one fw which adpots for following platform without much changes:
nrf9160 DK
nrf Thingy 91
Both board has nrf52 onboard so, my idea is as...
