I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hi Nordic support:
Our product uses nRF9151 module, we are going to do GCF certification field test. Could you provide some guidance on the following issue?
How can...
I am using nRF52833 PCA10100 board. While trying to run sample ble code in segger embedded studio, I am frequently facing this error which says, .text file is larger than...
I am setting up Segger Embedded Studio on my M2 Macbook and running in issues.
I downloaded S140 (nRF5_SDK_17.1.0_ddde560) and upon the build, I see the following errors...
I have a nrf9160dk that drives a screen via SPI, using an IT8951 controller. The firmware driving the screen works fine if I plug the USB cable on a power bank or using MS...
Hi, I'm getting an error when building the example program blinky that says: ".text is larger than specified size" and ".rodata is larger than specified size".
I'm using...
I'm following the steps in exercise 1 of the nRF Connect SDK Fundamentals and getting configuration failures. From what I can tell it looks like Zephyr is failing to build...
nRF Connect SDK v3.2.0
Write code:
Read code:
Log:
The address seen on the phone is usually not "06 05 04 03 02 01", but sometimes it is "06 05 04 03 02...
After the PPK II had been stored for a long period of time, it was recently taken out to measure current. It was observed that, regardless of whether Source Meter mode or...
Hi all,
I have been attempting to get the nRF Connect VS Code extension setup to try out some samples on the nRF9161-DK board.
I'm currently having a problem with a version...
Clarify the minimum mandatory external connections and pin/rail requirements for an nRF9151 to boot and run a flashed application, and determine why serial_lte_modem (SLM...
Hi,
I'm working on an application that I recently updated to ncs v3.1.0 (from v2.9.1). For most of the development, I have been working with the nrf54l15 as build target...
HI
I have replaced the external flash used with the nRF54L15 with a different model. How should I set the sfdp-bfp parameters for this new flash?
Thanks!
Using nRF5340-DK, nRF Connect for VS Code 2026.1, ncs v3.1.1 I'm interfacing over a SPI bus to a custom ASIC that uses MISO as a sort of RTS/CTS kind of idea. While CS is...
Hello,
I'm experiencing an issue where RTT logs stop appearing after MCUboot jumps to the application on nRF52832. The application is running correctly (BLE advertising...
