Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi teams,
I want to find GAP address of sending node after received message.
In client model callback, there is access_message_rx_meta_t argument, and I can get unicast...
I am using an nRF520 PCA10040 dev board with a nRF52832 module and I am trying to get the ble_app_uart_pca10040_s132 FW to run using the SES segger tool set. After about 1...
Still having trouble getting a simple Blinky example running on two nRF52840 DK boards configured for a long range PHY_CODED connection.
I've looked through this post -...
I am new to the Nordic SDK and Segger embedded studio, and I am trying to test my NRF52840 dev board.
I am running the "ble_app_blinky_pca10056_s140" example, and I want...
1. Background info
We're developing a new IDE for microcontrollers (see https://embeetle.com ) and would like to support a range of Nordic Semiconductor microcontrollers...
1. Intro
We're developing a new IDE for microcontrollers (see https://embeetle.com ) and would like to support a range of Nordic Semiconductor microcontrollers. We received...
Hi,
In case of nRF52810, is it possible to implement both Master and Slave Mode ?
Also, this has do be done while the product being able to work with AT Commands.
...
Power Profiler V2.3.1
Hi,
I recently started doing power testing on one of our boards using the power profiler kit. I wanted to tested current consumption at different...
Hi Nordic Community,
I am trying to build a network using the OpenThread protocol and the nRF52840 chip. I have several Dongles, but I can't figure out how to flash the...
I'm importing ble_app_blinky_pca10040_s132 example in segger IDE. I'm using EVK-NINA-B1 and from nRF SDK I'm trying to importing example but getting error as mentioned in...
I have an external clock running at 3Mhz which I'd like to align with in software. Consider this contrived example:
What would the consequences be of attempting to read...
Hi,
I'm very new to c programming and your hardware. Please excuse my novice questions.
I'm making a rotary braille display using nRF52840 dongle (PCA10059) as it's brain...
Hi,
I using custom nrf52840 board .I have loaded the Bluetooth program in to the custom board using swdio/swclk/vtg/gnddetect these lines.There is no problem in Bluetooth...
I'm attempting to get MMD set up in an IAR project following this tutorial: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/monitor-mode-debugging---revolutionize...
Dear sir, We are using BL654PA from Laird technologies. We want to check RSSI at 2402MHz, 2440Mhz, 2480Mhz. Can you guide us how to enable PA without using Nordic stack file...
