In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
So I've been trying to integrate the ble_nus part of the ble_app_uart example into another project. All inits and sdk_config options seem to be the same.
Still, whenever...
Hi,
I want to read a IC register over SPI.
This is msp430 code,it works. Just
CS low
write address
write 0x00
CS high
I use SPIM, this is initialization
...
Using an nRF52832 with SDK15.2 can I have multiple SPI devices;
one with DMA and one without DMA?
And can one instance be of legacy type (nrf_drv_spi) and the other be...
We use Rigado BMD-300 module with nRF52832 and softdevice S132 v6.1.0 as peripheral. Trying to create test plan for Bluetooth qualification , but with new TCLR there are inconsistencies...
Hi,
Recently, I faced very weird problem which stops working MCU when MCU enters low-power mode.
Not all PCBA I made have the same problem but quite many PCBA shows the...
hello, this is my first time to start the PPK, I have a 52840 DK (BMD-340-EVAL) and PPK, when I use nRF connect to connect the PPK(PPK is over the 52840 DK) , it shows Failed...
Hi Nordic Community
I'm busy developing a board around the nRF9160. Do you have a KiCad library/component for the SOC, do I need to make one myself, and if you do have one...
I'm trying to use the SPIM driver on nRF52832. The setup is:
Chip: nRF52832
SDK: 15
Softdevice: s132 v6
Toolchain: GCC
For some reason the call to nrfx_spim_xfer...
Hello,
I'm trying to configure the max -min of interval params and supervision timeout to obtain timeout of android = 1s.
i configure all parameters to run function...
Hi,
I am using the nrf-52840 DK.
I modified the pwm_library to output 125khz frequency.
app_pwm_config_t pwm1_cfg = APP_PWM_DEFAULT_CONFIG_2CH(125000L, NRF_GPIO_PIN_MAP...
Hi ,
The nrf connect for desktop programming works good on my desktop before.
The tool shows error message "cannot find module 'usb' " today.
I ever try re-install the...
I am working on integrated peripheral and central device used for indoor positioning. The device has two modes, at boot it is a peripheral for some duration of time then it...
Hello, we have been using a nRF51822 8-pin RF module for a while now for various products, the pinout is as follows: power, P0.00, P0.01, P0.09, P0.11, SWDIO, SWDCLK, ground...
Hi I try to implement DFU to our application using Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0 When I use the DFU-Example everything works fine. I then implemented the DFU-code from...
