Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
I'm working with LEDs in a ble example
I'm calling ble_notification_init() and activate the LED in the callback handler.
I get sd_nvic_ClearPendingIRQ, sd_nvic_SetPriority...
Is there a way to get the RSSI value of a message using the standard functions within the sdk for mesh. I am currently using a modified version of the simple_on_off client...
Hi all
I'm trying to send 180 bytes using sd_ble_gattc_write(). Writing 20 bytes at a time with the BLE_GATT_OP_WRITE_REQ write_op works. But now I'm trying to speed things...
When I tried S110 examples like BLE proximity, beacon and hrs on QFAC, it works without any problem. Unfortunatelly I can not see any activity on pin VDD_PA of CDAB. Is there...
Hello.
I used NRF51822 Dongle(Central) and Peripheral.
I want to change from Dongle(Central) to PC(Central).
PC version is window8.1.
but not operation bluetooth communication...
In the examples I see places where there is conditional code based on the #define HOST.
For example in function nrf_mesh_init() i see that the softdevice is only enabled...
Hello,
My team and I are experiencing a problem with our custom DFU Bootloader, which is based on the Experimental Bootloader Secure Serial example (SDK 13), running in...
Hello,
I'm reading on github.com/.../Android-DFU-Library that there is a support for higher MTU on DFU. Is there an example how i should test it?
I'm tring to increase...
Hi,
I have one chip use the VDD and GND pins on the PCA10028 and I use nRF current measurement pin monitor the current.
My question is:
Does nRF current measurement monitor...
Environment:
mesh SDK: V0.10.1
example: light_switch
compile and download IDE: SEGGER embedded studio v3.26a
Problem:
light onoff server and client can not...
I am using the ble_app_hrs_nfc_pairing example (sdk 14.0.0) on my NRF52840 with the s140 soft device. I am able to bond with my phone (Android 8.0.0 Oreo) by tapping the sensor...
Hello:
I need to disable an interrupt event outside the handler. During debugging when the nrf_drv_gpiote_in_event_disable function gets executed, the program seems to...
Hello , I want to save some data,even thought there is no power.eg. device name ,baudrate.I have try to use flash write example.How can i read or write data from a memory...
Hi all,
I have tried to mimic the LESC multi role example to my own app, but I dint have luck to pair it using LESC, MITM, and perform bonding and I received a SM_pairing_faill...
1、I down load the sdk about thingy52(about nordic 52832)，it is keil 5
2、the pack 《nRF5x-MDK-Pack-5-Clause-NOD》is down load,and it is install ok
3、but after steps2，when...
