Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi experts,
I habe a following issue. First I have tried to use nrfx_twi driver. There was any data send over I2C... So I have written own driver using the Datasheet and...
We are trying to send a large message via a BLE characteristic and to do that we have broken up the message payload into smaller fragments and calling bt_gatt_notify() repeatedly...
hi：
I use ble_app_uart routine, test the receiving rate, use the mobile phone to send data, 52832 receive the fastest can only be 10KB.
In addition, when the interval...
Hi
Compile the cli sample into a hex file,Download it to the board, read the hex file through the nRF Connect for Desktop Programmer tool, and then convert it to the bin...
Description:
Facing an issue with k_sleep() function misbehaving after few months due to the internal counter ticks crossed uint32_max values. Simulated the same by hardcoding...
Hi,
we are currently using NCS 2.0.2 on nRF52840 .
Is it possible to disable uart1 via pinctrl or another library during runtime and re-configure the rx/tx as gpios? ...
Hi,
I have met some problems while building the environment of pc-ble-driver-py. Error occurs in this command. The error points that I do not install git, but I have installed...
Hi, I'm new to nrf development. I was able to successfully install the SDK and toolchain using the toolchain manager. But when I'm trying to build a sample project "Blinky...
Target: nrf52 dev kit
Soft device: s132_nrf52_7.2.0_softdevice.hex
SDK: nrf5 sdk 17.1.0
Environment: IAR
Example modified: ble_app_rscs I am trying to modify the example...
Hello,
I am currently developing an LTE/LwM2M application on a custom board using the nRF9160 and NCS version 2.1.0. The application is almost finished and works great,...
Hi team,
We are using NRF52833 with PCA10100 on it and soft device version is s140.
We are advertising with both service data and manufacturing data.
1. Initially when...
There are two UART interfaces in nRF52840:
We have refer to nRF52840 and nRF52840 DK materials, but we found only one UART connection reference.
We want to know how to...
Hello, team.
I have some questions about reset restriction of nrf9160.
Q1. Does the restriction timer(30minutes) still run after +CFUN=0?
Q2. What is the exact meaning...
Hi guys. I read this thread answered by Einar Thorsrud. devzone.nordicsemi.com/.../direct-advertising-example
"HID mouse example uses direct advertising, but only when it...
